Publicidad
Idiomas disponibles
Idiomas disponibles
using more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
MiniMUM gAUgE FOR CORD sETs
Total length of Cord in Feet (meters)
Volts
120V
25 (7.6)
240V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More
not
More
Than
Than
0
6
18
6
10
18
10
12
16
12
16
14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V .......................... volts
Hz ........................hertz
min ......................minutes
or DC ......direct current
....................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per minute
RPM .................... revolutions per minute
sfpm ................... surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories. An
accidental start‑up can cause injury.
Cage Carrying Handles (Fig. A, B)
This pressure washer has a protective cage that protects the
pressure washer from daily jobsite abuse but also provides
mulitiple carry handle
14
using whichever part of the cage that is convenient for
50 (15.2) 100 (30.5) 150 (45.7)
American Wire gauge
16
16
16
14
16
14
12
Not Recommended
or AC/DC .... alternating or
direct current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all documentation
..................... do not expose to rain
options. Carry the pressure washer
your application. DO nOT attempt to carry the pressure washer
by the hose storage brace
Telescoping Handle (Fig. A, C)
This pressure washer has a convenient, built in telescoping
handle and transport wheels.
1. To unlock the telescoping handle
release button
hear an audible click when it snaps into position.
2. To store the telescoping handle
release button
down and into the pressure washer body. You will hear an
audible click when it snaps into position.
3. To move the pressure washer
14
transport wheels
12
unit by the telescoping handle.
12
Accessory Storage Compartment (Fig. D)
This pressure washer has a built in accessory storage
compartment
handle grip and turbo nozzle.
1. To unlock the storage door
latch
11
counterclockwise and flip the door open
to access the spray wand
grip
5
, and turbo nozzle
2. To lock the storage door
closed position. Rotate the door latch
the storage door into position.
Assembling Spray Wand (Fig. E)
1. To connect the spray handle
insert the threaded end of the spray handle onto the
threaded end of the handle grip. Rotate the spray handle
clockwise until fully tightened.
2. To connect the spray wand
the threaded end of the spray wand into the threaded
collar
31
of the spray handle. Rotate the threaded
collar
31
clockwise until fully tightened.
High Pressure Hose Storage (Fig. F)
This pressure washer has a built in storage area to carry the
high pressure hose. The coiled hose is secured between the
hose storage brace
1. To access the high pressure hose
storage latch
away from the pressure washer unit
2. Remove the hose from the pressure washer unit
3. Swing the hose storage brace
the hose storage latch
brace
28
Attaching High Pressure Hose (Fig. G)
CAUTION: NEVER PULL WATER SUPPLY HOSE TO
MOVE pressure washer. This could damage hose and/
or pump inlet.
nOTE: Uncoil the high pressure hose
prevent kinks.
28
or telescoping handle
12
13
and slide the handle upwards. You will
12
, press the handle
13
and slide the telescoping handle
8
, tilt the unit so the
15
are touching the ground and pull the
30
to carry the spray wand, spray handle,
10
, rotate the door
2
, spray handle
22
.
10
, place the storage door in the
4
to the handle grip
2
to the spray handle
28
and the pressure washer unit
1
29
and swing the hose storage brace
28
closed and lock
29
securing the hose storage
to the pressure washer unit
1
English
12
.
, press the handle
4
, handle
11
clockwise to lock
5
,
4
4
, insert
8
.
, unlock the hose
28
8
.
8
.
8
.
before installation to
7
Publicidad
