Publicidad
Idiomas disponibles
Idiomas disponibles
USING THE PRECISION PROCESSOR® BOWL
IMPORTANT:
• Review all warnings at the beginning of this Owner's Guide before proceeding.
• As a safety feature, if the blade assembly is not fully seated, you will not be able to install and lock the lid.
NOTE: DO NOT add ingredients before completing installation of the blade assembly.
1
Plug in motor base and place on a clean, dry, level surface such
as a countertop or table.
2
Lower the Precision Processor Bowl onto the motor base and
rotate clockwise until it clicks into place.
3
Exercising care, grasp the Chopping Blade Assembly by the
top of the shaft and place it onto the drive gear inside the
bowl. Note that the Chopping Blade Assembly will fit loosely
onto the drive gear.
4 Add ingredients to the bowl, making sure not to exceed the
MAX FILL line.
5
Place lid on the bowl, with black line on tab aligned slightly to
the right of tab on front of bowl. Turn lid clockwise to lock in
place. When properly locked, the white line on lid will line up
with the black line on bowl. Once the lid is locked in place,
press the Power button to turn unit on. The available program
buttons will illuminate and the unit will be ready for use.
6a If using an Auto-iQ® program, first select the program that
best suits your recipe. The preset feature will automatically
stop the unit at the end of the program. To stop the unit at
any time, press the currently active program again.
6b If using a manual program, select your desired speed. Once
the ingredients have reached your desired consistency,
press the active button again, or wait 60 seconds for the
unit to come to a complete stop.
7
To remove the bowl from the motor base, turn the bowl
counterclockwise and then lift up.
8
Remove the lid by pressing the RELEASE button on the front tab and
then lifting up on the handle. Always remove the Chopping Blade
Assembly before emptying the ingredients from the bowl. To remove
the Chopping Blade Assembly, carefully grasp it by the top of the shaft
and lift it out of the bowl.
9 Turn the unit off by pressing the Power button. Unplug the unit when
finished. Refer to the Care & Maintenance section for cleaning and
storage instructions.
ninjakitchen.com
ninjakitchen.com
CARE & MAINTENANCE
CLEANING
Separate all parts. Wash all containers in warm, soapy water with a soft cloth.
• Hand-Washing
Wash blade assemblies in warm, soapy water using a dishwashing utensil with a handle to avoid
direct contact with the blades. Exercise care when handling blade assemblies as the blades are sharp.
Thoroughly rinse and air-dry all parts.
• Dishwasher
All attachments are dishwasher safe. It is recommended that the lids, containers, and blade assemblies
be placed on the top rack of the dishwasher ONLY. Ensure the blade assemblies are removed from
their containers before placing in the dishwasher. Exercise care when handling blade assemblies.
• Motor Base
Turn off the unit and unplug the motor base before cleaning. Wipe motor base with a clean, damp cloth.
DO NOT use abrasive cloths, pads, or brushes to clean the base.
STORING
Wrap the power cord around the cord wrap on the back of the motor base. Store the unit upright and
store all blade assemblies inside or attached to their respective containers with their lids locked in place.
DO NOT store blended or unblended ingredients in the Single-Serve Cup with the Pro Extractor Blades®
assembly attached.
DO NOT stack items on top of the containers. Store any remaining attachments alongside the unit or in
a cabinet where they will not be damaged or create a hazard.
RESETTING THE MOTOR
This unit features a unique safety system that prevents damage to the motor and drive system should
you inadvertently overload the it. If the unit is overloaded, the motor will be temporarily disabled. Should
this occur, follow the reset procedure below.
1 Unplug the unit from the electrical outlet.
2 Allow the unit to cool for approximately 15 minutes.
3 Remove the container's lid and blade assembly. Empty the container and ensure no ingredients are
jamming the blade assembly.
IMPORTANT: Ensure that maximum capacities are not exceeded. This is the most typical cause of
appliance overload.
If your unit needs servicing, please call Customer Service at 1-877-646-5288. So we may better assist you,
please register your product online at registeryourninja.com and have the product on hand when you call.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, visit ninjaaccessories.com.
ninjakitchen.com
ninjakitchen.com
Publicidad
