IKEA LAGAN Manual Del Usuario página 5

ENGLISH
Product description
7
8
9
11
First Use
Advice regarding the first time use
Before installation and first usage of the appliance please read
carefully „ SAFETY INSTRUCTION" and „ASSEMBLY INSTRUCTION"
available in the product literature bag. Please remember to
remove all transport protection parts from the dishwasher.
Filling the salt reservoir
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine's functional components.
• It is mandatory that THE SALT RESERVOIR BE NEVER EMPTY.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and should be filled when the
SALT REFILL indicator light
1. Remove the lower rack and unscrew
2. Position the funnel (see figure) and
3. Only the first time you do this: fill
4. Remove the funnel and wipe any
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash program (this could
damage the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading.
Only use salt that has been specifically designed for
dishwashers. If the salt container is not filled, the water
softener and the heating element may be damaged
as a result of limescale accumulation. Using of Salt is
recommended with any type of dishwasher detergent.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle to
avoid corrosion.
1
2
3
4
5
6
10
in the control panel is lit.
the reservoir cap (anticlockwise).
fill the salt reservoir right up to its
edge (approximately 1 kg); it is not
unusual for a little water to leak out.
the salt reservoir with water.
salt residue away from the opening.
To download the full version visit www.ikea.com
1 Upper rack
2 Foldable flaps
3 Upper rack height adjuster
4 Upper sprayer arm
5
Lower rack
6 Cutlery basket
7 Lower sprayer arm
8 Filter Assembly
9 Salt reservoir
10 Detergent and Rinse Aid dispensers
11 Control panel
Setting the water hardness
To allow the water softener to work in a perfect way, it is
essential that the water hardness setting is based on the actual
water hardness in your house. This information can be obtained
from your local water supplier. The factory sets the default value
for the water hardness.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing quickly the ON/OFF
button.
• The program indicator light of the current set level flashes.
• Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level °dH German
degrees
1 Soft 0 - 6
2 Medium 7 - 11
3 Average 12 - 16
4 Hard 17 - 34
5 Very hard 35 - 50
Water Softening System
Water softener automatically reduces water hardness, conse­
quently preventing scale buildup on heater, contributing also
to better cleaning efficiency. This system regenerates itself with
salt, therefore it is required to refill salt container when empty.
Frequency of regeneration depends on water hardness level
setting ­ regeneration takes place once per 6 Eco cycles with
water hardness level set to 3.
Regeneration process starts in final rinse and finishes in drying
phase, before cycle ends.
• Single regeneration consumes: ~3.5 L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005 kWh of energy.
°fH French °Clark English
degrees degrees
0 - 10 0 - 7
11 - 20 8 - 14
21 - 29 15 - 20
30 - 60 21 - 42
61 - 90 43 - 62
5