Dreame Vortech Z10 Manual De Usuario página 14

• Before cleaning the dust cup, please
EN
confirm that the plug is disconnected
and keep the vacuum's power button in
the off position.
• If the vacuum is not used for an extended
period, fully charge it, unplug the power
cord, remove the battery, and store it
in a cool, low-humidity environment
away from direct sunlight. To avoid over-
discharging the battery, recharge the
battery at least once every three months.
Cleaning the Vacuum
Wipe the vacuum with a soft dry cloth.
Cleaning the Dust Cup, Pre-
Filter, and Cyclone Assembly
1. Press the dust cup release button and
remove it from the vacuum.
2. Remove the pre-filter first, and then
rotate the cyclone system to lift it out.
3. Rinse the cyclone assembly, pre-filter,
and dust cup until they are clean. After
washing, air dry for at least 24 hours.
Fig. E-1-Fig. E-3
Note:
• Please clean the dust cup as needed.
• It is recommended to clean the cyclone
system and pre-filter at least once every
3 to 4 months.
Installing the Dust Cup, Pre-
Filter, and Cyclone Assembly
1. Install the cyclone assembly and pre-
filter into the dust cup.
2. Slightly tilt the dust cup so the slot
aligns with the clip on the vacuum. Then
gently push the dust cup until it clicks
into place.
Fig. E-4-Fig. E-5
Cleaning the Filter
It is recommended to clean the filter
once every 4 to 6 months.
1. Remove the dust cup as shown in the
figure.
7
2. Remove the filter from the vacuum by
pulling it down in the direction shown in
the figure.
3.Rinse the filter with rotating it 360° .
Lightly tap the filter several times to
remove any debris caught in it.
4. Allow the filter to air dry for 24 hours.
Fig. E-6-Fig. E-9
Note:
• Only use clean water to wash the filter.
Do not use detergent.
• Do not attempt to clean the filter with a
brush or finger.
Installing the filter
1. Insert the filter into the vacuum and
gently press down, as illustrated.
2. Reinstall the dust cup.
Fig. E-10-Fig. E-11
Cleaning the Air Outlet Filter
1. Remove the air outlet filter as shown in
the figure.
2. Lightly tap the filter several times to take
out any dust and debris caught in it.
3. Reinstall the filter.
Fig. E-12-Fig. E-14
Note: The air outlet filter is non washable.
It is recommended to clean the filter once
every 4 to 6 months.
Replace the dust collection bag
When the dust collection status indicator
blinks orange, it means that the dust
collection bag reaches capacity and needs
to be replaced with a new one.
1. Take off the dust-removal hub cover.
2. Pull out the dust collection bag and
discard it.
Note: Pulling outwards on the handle of
the dust collection bag will seal the bag to
prevent the dust and debris from accidentally
falling out.
3. When the filter is dirty, rinse it with
water. Then place it in a well-ventilated
place for at least 24 hours to make sure it
is thoroughly dry.
4. Install a new dust collection bag by
inserting the bag handle into the card
slot.
5. Install back the dust-removal hub cover.
Fig. E-15-Fig. E-19
Note: It is recommended to replace the
dust collection bag every two months. If the
dust collection bag reaches capacity, the
indicator blinks orange.
Replacing the Battery Pack
The vacuum contains a removable
rechargeable lithium-ion battery pack
which has a limited number of recharge
cycles. After extended use, the battery
pack may no longer hold a charge. If this
happens, it means the battery pack has
reached the end of its life cycle and needs
to be replaced.
1. Press down the battery pack release
button and slide the battery pack to the
right, as illustrated, to remove it.
2. Install the new battery pack.
Fig. E-20
Cleaning the Multi-Surface
Brush
1. Turn the lock counterclockwise until it
stops, then remove the roller from the
roller brush.
2. Use scissors to cut off the hairs and
fibers that get stuck on the brush roller.
Wipe the dust from the notch and
transparent cover with a dry cloth or
paper towel. Thoroughly dry before
use.
3. When it is dirty, rinse the brush roller
with clean water until it is clean.
4. Stand the brush roller upright for at
least 24 hours until it is fully dry.
Fig. E-21-Fig. E-24
Cleaning the Soft Roller Brush
1. As shown in the picture, press the
brush roller release button to remove
the roller from the slot.
2. Use scissors to cut off the hairs and
fibers that get stuck on the brush roller.
Wipe the dust from the notch and
transparent cover with a dry cloth or
paper towel. Thoroughly dry before
use.
3. When it is dirty, rinse the brush roller
with clean water until it is clean.
4. Stand the brush roller upright for at
least 24 hours until it is fully dry.
Fig. E-25-Fig. E-28
Cleaning the Motorized Mini-
Brush
1. Use a coin as illustrated to rotate the
lock counterclockwise until you hear a
click.
2. After unlocking the motorized mini-brush,
remove the brush roller, then rinse and
clean it.
3. Stand the brush roller upright in a well-
ventilated area for at least 24 hours until
it is fully dry.
4. Once the brush roller is dry, reinstall it
by following the disassembly steps in
reverse.
Fig. E-29-Fig. E-32
EN
8