DeWalt DCF787 Traducido De Las Instrucciones Originales página 19

nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Worklights (Fig. A)
There is a worklight 7 located above the trigger switch
worklight will be activated when the trigger switch is depressed.
When the trigger is released, the worklight will stay illuminated
for up to 20 seconds. If the trigger switch remains depressed,
the worklights will remain on.
nOTE: The worklight is for lighting the immediate work surface
and are not intended to be used as a flashlight.
Quick-Release Chuck (Fig. A, C)

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition. Inspect
accessory prior to use to ensure that it con tains no cracks.
nOTE: The chuck accepts 6.35 mm hex accessories and
25.4 mm bit tips only. Using 25.4 mm bits allows better access
in tight spaces.
Place the forward/reverse button
position or remove battery pack before changing accessories.
To install an accessory, push accessory to fully insert into
chuck 4 . The chuck collar 3
lock accessory in place.
To remove an accessory, pull the chuck collar away from the
front of the tool. Remove the accessory and release the collar.
Usage
Your impact tool generates the following maximum torque:
Cat # Nm
DCF787 170

CAUTION: Ensure fastener and/or system will withstand the
level of torque generated by the tool. Excessive torque may cause
breakage and possible personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Release the switch to stop
operation. Always check torque with a torque wrench, as the
fastening torque is affected by many factors including the
following:
• Voltage: Low voltage, due to a nearly discharged battery, will
reduce fastening torque.
• Accessory size: Failure to use the correct accessory size will
cause a reduction in fastening torque.
• Bolt Size: Larger bolt diameters generally require higher
fastening torque. Fastening torque will also vary according to
length, grade, and torque coefficient.
• Bolt: Ensure that all threads are free of rust and other debris to
allow proper fastening torque.
• Material: The type of material and surface finish of the material
will affect fastening torque.
• Fastening Time: Longer fasten ing time results in increased
fastening torque. Using a longer fastening time than recom-
mended could cause the fasteners to be overstressed, stripped
or damaged.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
1
2 in the locked off (centre)
does not need to be pulled up to
Ft.-Lbs. In.-Lbs
125 1500

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
The charger and battery pack are not serviceable.
. The
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing with
dry air as often as dirt is seen collecting in and around the air
vents. Wear approved eye protection and approved dust mask
when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous.

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition. Inspect
accessories prior to use to ensure that they contain no cracks.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a local
recycling station. The collected battery packs will be recycled or
disposed of properly.
EnGLIsh
19