Fein AGSZ18-280BL AS Instrucciones De Uso página 6

en
6
Use clamps to support workpiece whenever
practical. Never hold a small workpiece in
one hand and the tool in the other hand
while in use. Clamping a small workpiece
allows you to use your hand(s) to control
the tool. Round material such as dowel rods,
pipes or tubing have a tendency to roll while
being cut, and may cause the bit to bind or
jump toward you.
Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and
pull the power tool out of your control.
After changing the bits or making any
adjustments, make sure the collet nut,
chuck or any other adjustment devices are
securely tightened. Loose adjustment
devices can unexpectedly shift, causing loss
of control, loose rotating components will
be violently thrown.
Do not run the power tool while carrying it at
your side. Accidental contact with the spin-
ning accessory could snag your clothing,
pulling the accessory into your body.
Regularly clean the power tool's air vents.
The motor's fan will draw the dust inside the
housing and excessive accumulation of pow-
dered metal may cause electrical hazards.
Do not operate the power tool near flamma-
ble materials. Sparks could ignite these
materials.
Do not use accessories that require liquid
coolants. Using water or other liquid cool-
ants may result in electrocution or shock.
Further safety instructions for all
operations
Kickback and related warnings
Kickback is a sudden reaction to a pinched
or snagged rotating wheel, sanding band,
brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating
accessory which in turn causes the uncon-
trolled power tool to be forced in the direc-
tion opposite of the accessory's rotation.
For example, if an abrasive wheel is snagged
or pinched by the workpiece, the edge of
the wheel that is entering into the pinch
point can dig into the surface of the material
causing the wheel to climb out or kick out.
The wheel may either jump toward or away
from the operator, depending on direction
of the wheel's movement at the point of
pinching. Abrasive wheels may also break
under these conditions.
Kickback is the result of power tool misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below.
Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. The operator can
control kickback forces, if proper precau-
tions are taken.
Use special care when working corners,
sharp edges etc. Avoid bouncing and snag-
ging the accessory. Corners, sharp edges or
bouncing have a tendency to snag the rotat-
ing accessory and cause loss of control or
kickback.
Do not attach a toothed saw blade. Such
blades create frequent kickback or loss of
control.
Always feed the bit into the material in the
same direction as the cutting edge is exiting
from the material (which is the same direc-
tion as the chips are thrown). Feeding the
tool in the wrong direction causes the cut-
ting edge of the bit to climb out of the work
and pull the tool in the direction of this feed.
When using rotary files, cut-off wheels,
high-speed cutters or tungsten carbide cut-
ters, always have the work securely
clamped. These wheels will grab if they
become slightly canted in the groove, and
can kickback. When a cut-off wheel grabs,
the wheel itself usually breaks. When a
rotary file, high-speed cutter or tungsten
carbide cutter grabs, it may jump from the
groove and you could lose control of the
tool.
Additional safety instructions for
grinding and cutting-off operations
Safety warnings specific for grinding
and abrasive cutting-off operations:
Use only wheel types that are recommended
for your power tool and only for recom-
mended applications. For example: do not
grind with the side of a cut-off wheel. Abra-
sive cut-off wheels are intended for periph-
eral grinding, side forces applied to these
wheels may cause them to shatter.