Publicidad
Idiomas disponibles
Idiomas disponibles
() Power switch
Depress
this switch
to turn power
on and depress once
more
to
put the unit in the stand-by mode.
Note:
In the STAND-BY
position the AC mains power will stil! be -
supplied to the graphic equalizer. Therefore when
not in use
unplug the mains lead from the socket.
2) Equalization controls
When
the equalizer
switch Gis
in the ON
(<=)
position, the
equalization
controls
raise
and
lower
the
response
of the
cor-
responding frequency band by up to +10 cB.
@) Level control
Use this contro!
to lower the overall output level when the signal
level is so high that sound is distorted.
(4) Tape monitor switch (TAPE MONITOR)
Set this switch
to OFF
(£1)
to
listen
to a turntable
or tuner.
Depress to ON
(=)
to listen to a tape deck.
If a separate noise reduction system is used, it should be connected
between
the graphic equalizer and the tape deck. When
recording
through the noise reduction unit, set the equalizer recording switch
() to OFF
(C1) to turn off the equalization circuitry so that the
noise reduction system can take effect.
Operate the amplifier with its tape monitor switch set to '''TAPE".
1. When operating through the equalizer circuit:
Equalizer
Tape
recording
monitor
switch
switch
Equalizer
Source
een
Listening
to
Recording
(5) Equalizer switch (EQUALIZER)
Depress this switch to ON
(<) to activate the graphic equalizer
circuitry. In the OFF
(L)
position, the input signal goes direct-
ly to the output terminals without
passing through the equalizer
circuit and the equalization controls have no effect on the sound.
©) Equalizer recording switch (EQUALIZER REC)
Depress this switch to ON
{+=) to record
a signal through the
equalizer circuitry.
Set to OFF
(1)
to make
a recording with-
out the equalizer circuitry or through a noise reduction system.
@) Equalizer recording indicator
Power indicator
Note:
if the tape monitor switch ts on, it will not be possible to record the
equalized source signal even though the equalizer recording indicator
remains lit. Always turn the tape monitor switch off before recording
the equalized signal.
Note:
@
Confirm
that the amplifier
power
switch
is off before
making any connections.
e
Insert all plugs firmly. Loose connections can result in
noise and other problems.
2. When not operating through the equalizer circuit:
;
Equalizer
Tape
Equalizer
;
;
Source
ch
recording
monitor
yore
switch
switch
r
;
aes
'pa
TL
pa 2
=
OFF
OFF
O N
Listening
disc
to &
radio
1.
sae
—
etc.
OFF
OFF
OFF
recording
Note:
When
using this unit with a noise reduction system, be sure
the equalizer recording switch @) is OFF
(£2) so that the
noise reduction effect is not altered by the settings of the
equalization controls.
Power:
220V/50 Hz for Europe
Power consumption:
6W
Weight:
2.7 kg
Dimensions:
A20(W) x 87(H) x 263(D) mm
Channels:
2
Frequency bands:
10
Gain:
O dB (Control knob position: ''0'')
Control range:
+10 dB
Maximum output:
5V (at 1 kHz, THD 0.05%, Load 47 k&)
Input impedance:
47 kQ
Output impedance:
2 kQ
S/N ratio:
110 dB (Input short, A network)
Total harmonic
distortion:
Less than 0.01% (20 Hz to 20 kHz
at 1V output)
e
Specifications and design are subject to change without notice.
Publicidad
