Publicidad
Idiomas disponibles
Idiomas disponibles
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explosion.
Penetrating a water line causes property damage
or may cause an electric shock.
b. Release the On/Off switch and set it to the off
position when the power supply is interrupted,
e. g., in case of a power failure or when the
mains plug is pulled.
c. Do not touch grinding and cutting discs before
they have cooled down. The discs can become
very hot while working.
d. Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure
than by hand.
KNOWING YOUR TOOL
PRODUCT DESCRIPTION AND
SPECIFICATIONS
Read all safety warnings and all
instructions, Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
INTENDED USE
The Mini Carver is intended for grinding, carving, and
sanding of metal, stone and wood without use of water.
Note: Text, diagrams and data are correct at time of
printing. In the interests of continuous improvement of
our products, technical specifications are subject to
alteration without prior notice.
For working with applications on materials that create
dust use dust extraction accessories.
Mini Carver
Voltage
Power rating
Frequency
Protection class
Rated speed
Tool diameter
Mounting bore size
Mounting screw size
Weight
UNPACKING AND ASSEMBLY
Inspect to ensure that no damage has occurred to the
tool and accessories during transport. If damaged,
report to the retailer immediately.
Remove the auxiliary handle from the box and attach
to the tool. (Fig. A)
The Mini Carver is packaged with a Mini Industrial
Blade fitted, ready for use. Ensure that the
clamping screw (18) is always fully tightened before use.
US/CAN
MIN.FG.900.20
V
120
A (W)
8 (960W)
Hz
60
II
II
Rpm
6000-18000
inch (mm)
2" (50mm)
inch (mm)
3/8" (9.5mm)
M5
lbs (kg)
4.4 (2kg)
PRODUCT FEATURES AND LIST OF
COMPONENTS
ITEM
Features and components
1
Mini Carver Body
2
Auxiliary handle
3
ON/OFF Switch
4
Speed control
5
Drive Lock button
6
Extension arm
7
Mini shaft
8
Bearings
9
Bearing cap
10
Pan screw 4g
11
Small Pulley
12
Large Pulley
13
Belt
14
Guard cover
15
Pan screw 6g
16
Mini Industrial Blade
17
Clamping Washer
18
Clamping screw M5
19
Dust extraction cover
20
Sanding Pad
21
Sandpaper
22
Clamping Bush
23
Countersunk screw
24
Diamond Cutting Disc*
25
Grinding Wheel*
Items marked with the * are not included in this pack
PRODUCT FEATURES AND LIST OF
COMPONENTS
Fig. A, Fig. B, Fig. C
MOUNTING TOOLS AND ACCESSORIES
WARNING: To reduce the risk of serious personal
injury, turn the tool off and disconnect from the
power source before making any adjustments or
removing/ installing tools or accessories.
1. REPLACING CARVING AND
GRINDING DISCS
Insert a flat screw driver into the mini shaft (7) to
prevent rotation, then remove the clamping screw (18)
using the Allen Key provided with the tool (Fig. D).
Replace the blade with other Arbortech recommended
product as shown on the following diagrams.
Place the new disc over the small pulley, ensuring it is
properly centered and seated flat against the pulley
face. Place the clamping washer (17) over the disc
then insert and tighten the clamping screw (18) in
order as shown (Fig. E). Ensure the marks on the disc
are visible and arrow of rotation is pointing in the same
direction as the arrow on the back of the guard.
WARNING: Failure to properly mount the discs over
the pulley could result in serious injuries or damage
the tool.
English
4
Publicidad
