Publicidad
Idiomas disponibles
Idiomas disponibles
4. With finger off the trigger, press the contact trip against
the work surface. Pull the trigger.
THE TOOL MUST CYCLE.
Adjusting Depth (Fig. E)
WARNING: To reduce risk of serious injury from accidental
actuation when attempting to adjust depth, ALWAYS:
-
Disconnect air supply and engage trigger lock.
-
Avoid contact with trigger during adjustments.
The depth that the fastener is driven can be adjusted using
the depth adjustment next to the trigger of the tool. The
depth of drive is factory adjusted to a nominal setting. Test
fire a fastener and check depth. If a change is desired:
1. To drive the nail shallower, rotate the depth adjustment
6
wheel
to the right.
2. To drive a nail deeper, rotate the depth adjustment
wheel to the left.
The adjustment knob has detents as it is rotated. Test drive
another fastener and check depth. Repeat as necessary to
achieve desired results. The amount of air pressure
required will vary depending on the size of the fastener
and the material being fastened. Experiment with the air
pressure setting to determine the lowest setting that will
consistently perform the job at hand. Air pressure in excess
of that required can cause premature wear and/or damage
to the tool.
VINYL SIDING ADAPTER ASSEMBLY
(Fig. F–K)
When using the vinyl siding adapter, the trigger must
be converted to the sequential gray trigger. Refer to
operator's manual for conversion instructions.
Only qualified personnel should repair the tool. If you
should have difficulty understanding the following
instructions contact a factory service center.
iMPORTAnT sAFETY insTRUCTiOns
WARNING:
-
Read and understand tool instruction manual before
attempting repairs.
-
Use only genuine replacement parts.
-
Always wear ANSI compliant eye and ear protection.
-
Disconnect air from tool and remove all nails before
servicing.
-
Always point tool in safe direction when
reconnecting air supply.
nOTiCE:
-
Do not allow dirt, dust or other foreign materials to
enter the tool.
Be careful not to scratch or damage the O-rings or
-
any internal surfaces.
nOTEs:
1. Note fit and orientation of all components when
disassembling and reassembling tool.
2. Exercise care not to nick or damage any of the machined
surfaces (which could cause an air leak).
3. After reassembly, test for proper tool operation as
explained in the operation manual.
COnVERT ROOFing nAilER COnTACT TRiP TO A VinYl
siDing COnTACT TRiP
1. Remove contact foot spring
2. Slide the safety contact tip
15
3. Rotate contact arm
out. Save this part to convert to roofing nailer contact
trip in future.
4. Slide the vinyl siding adapter
the contact arm.
5. Push the vinyl siding adapter up and install the contact foot
spring. There is a contact foot spring in the kit, if needed.
6. When operating the tool with the vinyl siding adapter,
the trigger must be converted from the contact trigger
(black) to the sequential trigger (gray). Refer to the
operation manual for conversion instructions.
Shingle Guide (Fig. L, M)
17
Adjust shingle guide
1. Loosen the adjusting screw
guide to desired position.
2. Tighten adjusting screw firmly.
The guide can be used as an aid to position the shingle being
nailed a specific distance from the front edge of the previous
19
row of shingles
as shown.
Clearing a Jammed Nail (Fig. N)
WARNING: Disconnect air line from tool, engage trigger
lock and remove fasteners from magazine before making
adjustments or personal injury may result.
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions to clear:
1. Disconnect the air supply from the tool.
3
2. Lift the door latch
.
4
3. Open the door
.
4. Remove the jammed nail.
5. Correct any deformation that may have occurred to the
nail coil.
nOTE: Should nails continue to jam frequently in nosepiece,
have tool serviced by an authorized D
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Make sure compressor tanks have been properly drained
prior to use.
2. Keep tool as warm as possible prior to use.
3. Make certain all fasteners have been removed from canister.
4. Put 5 to 7 drops of D
WALT pneumatic tool oil in the air inlet.
e
5. Lower air pressure to 80 psi (5.5 bar) or less.
6. Reconnect air and load nails into canister.
7. Actuate the tool 5 or 6 times into scrap lumber to
lubricate O-rings.
14
. Save this part for future use.
7
down.
up and slide safety contact tip
16
up into the opening in
:
18
and slide the shingle
WALT service center.
e
English
9
Publicidad
