Publicidad
Idiomas disponibles
Idiomas disponibles
GROUP I (9-18 KG) WITH 5-POINT HARNESS AND VEHICLE SEAT BELT
1.
Place child restraint forward-facing (in the direction of travel) in proper seating location, flat on the vehicle seat bottom and
touching vehicle seat-back.
2.
Select a forward-facing position from 1 to 3 (red).
3.
Pull the shoulder belt section through between the headrest and backrest. Place the lap belt section in the belt guidance 1.
4.
Pull out safety belt from the back to the side, lap belt section respectively from the belt guidance 1 of the base. One side of the
shoulder belt through the backrest and the belt guidance 1, another side along the upper inside.
5.
Fasten the vehicle seat belt. You will hear an audible CLICK! Pull the seat belt tight to make sure it is not twisted.
6.
By pressing your knee on the child seat, tighten the car belt as follows: pull on the lower part of the shoulder seat belt section near
the vehicle seat buckle to tighten the lap belt section.
NOTE: Test by pulling on the child restraint and shoulder belt to ensure it is locked.
GROUP I (9-18 KG) WITH 5-POINT HARNESS AND ISOFIX
1.
Place child restraint forward-facing (in the direction of travel) in proper seating location, flat on the vehicle seat bottom and
touching vehicle seat-back.
2.
Select a forward-facing position from 1 to 3 (red).
3.
Press the ISOFIX button to pull out the two ISOFIX locking arms from the base bottom.
hear an audible CLICK!
Ensure that the indicator turns into a red colour, which means ISOFIX
attachments are unlocked.
NOTE: The ISOFIX attachment points are located between the surface and the backrest of the vehicle
seat.
4.
Align ISOFIX attachments to the metal anchorages at the bottom of the car seat's backrest and
push it until it clicks.
You will hear an audible CLICK! Ensure both sides of the ISOFIX locking arms
turn into green safety colour.
CAUTION: After the ISOFIX installation check if the child restraint is securely fitted. If the child
restraint is not stable and is shaking, reinstall.
5.
First, pull out the belt from the belt ALR. Shoulder belt through the headrest and backrest. Place
the lab belt section in the belt guidance 1.
6.
Pull out safety belt from the back to the side, lap belt section respectively from the belt guidance 1 of
the base. Then, one side of the shoulder belt through the backrest and the belt guidance 1, another
side along the upper inside.
NOTE: Place both shoulder and lab vehicle seat belt behind the sleeping pads, between the backrest and
the sleeping pads.
7.
Fasten the vehicle seat belt. You will hear an audible CLICK! Pull the seat belt tight to make sure it is not twisted.
8.
By pressing your knee on the child seat, tighten the car belt as follows: pull on the lower part of the shoulder seat belt section near
the vehicle seat buckle to tighten the lap belt section.
GROUP II, III (15-36 KG) WITH VEHICLE SEAT BELT
NOTE: When using this child restraint in groups II or III, remove the 5-point harness, triangle pad, and sleeping pad.
1.
Place child restraint forward-facing (in the direction of travel) in proper seating location, flat on the vehicle seat bottom and
touching vehicle seat-back.
2.
Select a forward-facing
position 2
3.
First, pull out the belt from the belt ALR. Shoulder belt through the same side of guidance 2, lap belt through the same side of
guidance 1, then pull the shoulder belt and lap belt together through another side of guidance 1.
4.
To fasten the seat belt across child: lap portion of the vehicle seat belt should rest within both lower belt guides with buckle located
on the outside of the child restraint.
5.
Place shoulder portion into the upper belt guide on the headrest so that belt lays properly across child: on the collar bone, interior (A)
to the shoulder (B).
6.
Make sure seat belt is not twisted and remove slack from seatbelt so it lays flat, smooth and snug across child in all locations.
7.
Fasten the vehicle seat belt. You will hear an audible CLICK! Pull the seat belt tight to make sure it is not twisted.
CAUTION: The shoulder seat belt section must run diagonally backward. You can adjust the course of the belt with your vehicle's adjustable
belt deflector on both sides.
(red).
CLICK
You will
CLICK
EN
CLICK
43
Publicidad
