Publicidad
Idiomas disponibles
Idiomas disponibles
Weekly Timer
• To use the weekly timer, you must first set the current
time. The current time must be set when the appliance
is first put into operation and every time the appliance is
disconnected from the mains.
• The days of the week are indicated by the following digits
in the display:
Monday
P P =
Tuesday
P P =
Wednesday
P P =
Thursday
P P =
Set the Current Time:
1. Select the weekly mode with the button
P P .
shows
2. Press the button
. The starts flashing.
3. Select the current day of the week with the
ton. Confirm your entry with the button
time is displayed, the hours ( ) start flashing.
4. Set the current hour with the
your entry with the button
played, the minutes ( ) start flashing.
5. Set the current minutes with the button
6. Wait until the minutes stop flashing. The settings are
accepted. In the hour bar, the upper and lower bars of
the current hour flash.
Program the Weekly Timer
• The operating modes determine when the appliance is to
operate in which operating mode.
• Each line of the hour bar (
0
The appliance is activated for the selected full hour.
• The upper bar represents the full power of the appliance,
the lower bar represents half the power. If the bars of
the hour bar are not lit, the appliance is working in the
anti-frost function.
• The appliance must remain switched on in the "Weekly
Timer" operating mode for the function to work. To avoid
being disturbed by the display illumination, it can be
switched off as described above.
• If the appliance is in the activated hour, the set temper-
ature can be displayed or changed with the
button.
• Make sure that you do not maintain too long between
programming steps. The programming mode is automati-
cally terminated after 5 seconds!
1. If not already done, set the time and temperature as
described on page 17.
- Individual temperatures cannot be set during pro-
gramming. The temperature from the default settings
(page 17) are adopted.
2. Select the weekly timer mode with the button
hour bar, the upper and lower bars of the current hour
flash.
18
PC-GKH3119_IM
Friday
P P =
Saturday
P P =
Sunday
P P =
. The display
or
but-
. When the
or
button. Confirm
. When the time is dis-
or
.
) represents one hour.
4
8
12 16 20
or
. In the
3. Press the button
. The current day
flashing in the display.
4. Select the day of the week to be programmed (
P P ) with the button .
5. Select the anti-frost function ( ) with the button
6. Go to the desired start time with the button
7. Use the button
to select whether the appliance should
operate with full power ( ) or half power ( )
8. Move to the desired stop time with the
The bars become visible accordingly.
9. Wait until the
P P stops flashing. The settings are ac-
cepted. In the hour bar, the upper and lower bars of the
current hour flash.
- Do you want to set more than one heating period per
day, e. g. heating period 1 from 10 – 12 hrs, heating period
2 from 16 – 18 hrs. Program heating period 1 (points 1 – 8)
as described above. Immediately after point 8, start
again with point 5 to set heating period 2.
Deleting a Weekly Timer Programming
1. Select the weekly timer mode with the button
hour bar, the upper and lower bars of the current hour
flash.
2. Press the button
. The current day
starts flashing in the display.
3. With the button
, select the day of the week on which
previously programmed times are to be changed.
4. Select the anti-frost function ( ) with the button
5. Go forward or backward in time with the button
As soon as you reach the programmed time, it is deleted.
Open Window Detection
The appliance causes a temperature check at regular
intervals and switches off if the temperature drops by 5 °C
within 20 minutes.
1. Press the
button to switch on the function. The sym-
bol
appears in the display.
2. Press the button again to switch the function off. The
symbol
goes out.
- You can also activate and deactivate the function on the
appliance. To do this, press and hold the button
approx. 3 seconds.
Ending Operation
1. Press the
button to switch off the appliance.
2. Then pull the mains plug out of the socket.
Restore Factory Settings
Press and hold the
and
approx. 3 seconds. An acknowledgement tone sounds and
the appliance switches off. The factory settings are restored.
P P of the week starts
P P –
.
or
.
or
button.
. In the
P P of the week
.
or
.
for
buttons on the appliance for
01.09.23
Publicidad
