Lutron HomeWorks Interactive HW-RPM-4E-120 Instrucciones De Instalación

Installation Instructions
Note: This product is only to be used with
electronic low-voltage type transformers.
Use with standard magnetic low-voltage
transformers may damage the module and
void the warranty.
1. Turn power off to all feeds to the panel.
Danger - This panel may be fed by multiple
circuits. Locate and lock each supply circuit
breaker in the off position before proceeding.
2. Install the module's wires into the appropriate
terminal blocks and secure using 3.5 to 5 in-lbs
(.4 to .56 Nm) of torque (See Figure 1).
Danger - Modules are not approved to be
used anywhere other than in a HomeWorks or
HomeWorks Interactive panel (HW-PNL8,
HWI-PNL-8 or HWI-PNL-5).
3. Mount the module into the rough-in panel.
Start with position 1, then 2, then 3, etc. Do not
overtighten screws, torque to 20 in-lbs (2.25 Nm)
maximum (See Figure 2).
4. Check that all bypass jumpers are installed.
They will distribute power to each load and should
not be removed until after all modules and loads
are fully installed and proven.
5. Turn on input feed circuit breakers and check
that they do not trip. Each module is rated for a
maximum load of 9A (1080 Watts) per output at
60Hz and a total combined maximum load of 16A
(1920 Watts).
Danger - Only turn on input feed circuit
breakers when load wiring is complete and it is
safe to have power applied.
6. For any feed circuit breaker that trips, locate
the shorted load and resolve the wiring problem
before proceeding.
7. Turn power OFF to all feeds to the panel.
8. Loosen all five screws on the bypass jumpers.
9. Remove and store the bypass jumpers for
possible later use.
Caution - Bypass jumpers must be reused
whenever a circuit breaker is turned OFF to
work on a load. Damage caused by short
circuits and miswiring IS NOT COVERED by
the product warranty.
10. Turn ON input feed circuit breakers and check
that they do not trip.
11. For any feed circuit breaker that trips, locate
the shorted load and resolve the wiring problem
before proceeding.
HW-RPM-4E-120
Electronic Low-Voltage
Remote Power Module, 4 Circuits
TM
120V, 16A at 60Hz
Figure 1 - Remote Power Module Wiring
Five Position Bypass Jumper
DH
1
DH
2
DH
3
DH
4
H1
N
N
N
N
N
Module 1 Terminal Blocks shown. Torque
Terminal Blocks using 3.5 to 5 in-lbs (.4 to
.56 Nm). DO NOT overtighten.
Figure 2 - Mounting Location
HWI-PNL-5
5
4
3
2
1
This product may be covered under one or more of the following U.S. patents:
4,797,599; 4,889,999; 5,038,081; 5,170,068; 5,237,207 and corresponding foreign
patents. U.S. and foreign patents pending. Lutron and HomeWorks are registered
trademarks and HomeWorks Interactive is a trademark of Lutron Electronics Co.,
Inc. © 2000 Lutron Electronics Co., Inc.
Red 1
Red 2
Red 3
Red 4
Black
White
DH
1
DH
2
DH
3
DH
4
L
N
N
N 5
N
N
DH
1
DH
2
DH
3
DH
4
L
4
N
N
N
N
N
DH
1
DH
2
DH
3 3
DH
4
L
N
N
N
N
N
DH 2
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4 1
L
N
N
N
N
N
L
L
N
N
N
G
1
Diagnostic LED
Address Switch
4-Pin Connector
HWI-RPM-4E-120
Remote Power Module
HWI-PNL-8
8
DH
1
DH
2
DH
3
DH
8 4
L
N
N
7
N
N
N
DH
1
DH
2
DH
3 6
DH
7 4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
6 4
L
N
N
N
N
N 5
DH
1
DH
2
DH
3
5 DH
4
L
N
N
4
N
N
N
DH
1
DH
2
DH
3
DH
4 4
L
N
N
N
N
N
DH 3
1
DH
2
DH
3
3 DH
4
L
N
N
N
N
2
N
DH
1
DH
2
DH
3
2 DH
4
L
N
N
N
N
N
DH
1
DH
2
1
DH
3
DH
1
4
L
N
N
N
N
N
L
L
N
N
N
G
8 8
1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4
1 2 3 4 5 6 7 8 J3 1 2 3 4 5 6 7 8 J4 1 2 3 4 5 6 7 8 J5
G1 V1 G2 V2 G3 V3 G4 V4 G5 V5 G6 VG G7 V7 G8 V8 G9 V9 G10 V10 G11 V11 G12 V12
1 2 3 4