Bosch GRT 18V-33 Manual Original página 19

– Vibration emission value a
h
– Uncertainty K
That the declared vibration total value(s) and the declared
noise emission value(s) have been measured in accordance
with a standard test method and may be used for comparing
one machine with another.
That the declared vibration total value(s) and the declared
noise emission value(s) may also be used in a preliminary as-
sessment of exposure.
That the vibration and noise emissions during actual use of
the machine can differ from the declared total value depend-
ing on the ways in which the machine is used; and of the
need to identify safety measures to protect the operator that
are based on an estimation of exposure in the actual condi-
tions of use (taking account of all parts of the operating cycle
such as the times when the machine is switched off and
when it is running idle in addition to the trigger time).
Rechargeable battery
Bosch sells some cordless power tools without a re-
chargeable battery. You can tell whether a rechargeable bat-
tery is included with the power tool by looking at the pack-
aging.
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
The rechargeable battery has two locking levels to prevent
the battery from falling out if the battery release button is
pressed unintentionally. The rechargeable battery is held in
place by a spring when fitted in the power tool.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Bosch Power Tools
EN 50636-2-91
2
m/s 3.1
2
m/s = 1.3
Press the button for the battery charge indicator or to show
the state of charge. This is also possible when the battery is
removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Battery Maintenance
Use the following procedures to enable optimum usage of
the battery:
– Protect the battery against moisture and water.
– Store the machine and battery only within a temperature
range between –20 °C and 50 °C . As an example, do not
leave the battery in the car in summer.
English | 19
IEC 62841-4-4
3.6
= 1.3
Capacity
60–100 %
30–60 %
5–30 %
0–5 %
Capacity
80–100 %
60–80 %
40–60 %
20–40 %
5–20 %
0–5 %
F 016 L94 542 | (07.02.2023)