Husqvarna 130 Mark II Manual Del Usuario página 16

7. Fill the fuel tank of the product with the fuel mixture.
Fuel mixture ratio on page 15 .
See
To fill the fuel tank
1. Make sure that the fuel mixture is correct and that
the fuel mixture is in a fuel container with an antispill
valve.
2. If fuel is on the container, remove the unwanted fuel
and let the container dry.
3. Make sure that the area near the fuel tank cap is
clean.
4. Remove the fuel tank cap. (Fig. 38)
5. Shake the fuel container before you add the fuel
mixture to the fuel tank.
6. Put back the fuel tank cap.
To lubricate the saw chain
The product has an automatic lubrication system. Make
sure to only use the correct chain oil and obey the
instructions.
1. Use vegetable-based saw chain oil or a standard
chain oil.
2. Make sure that the area near the cap of the saw
chain oil tank is clean.
3. Remove the cap of the saw chain oil tank.
4. Fill the saw chain oil tank with the recommended
saw chain oil.
5. Put back the cap of the saw chain oil tank.
Before you start the engine
• Examine the product for missing, damaged, loose or
worn parts.
• Examine the nuts, screws and bolts.
• Examine the air filter.
• Examine the throttle trigger lockout and the throttle
control for correct operation.
• Examine the stop switch for correct operation.
• Examine the product for fuel leaks.
• Examine the saw chain sharpness and tension.
To start a cold engine
1. Move the front hand guard forward to engage the
chain brake. (Fig. 39)
2. Pull the choke control out and up.
3. Push the air purge bulb 6 times. (Fig. 40)
4. Hold the body of the product on the ground with your
left hand.
5. Put your right foot through the rear handle.
6. Pull the starter rope handle slowly with your right
hand until you feel some resistance.
7. Pull the starter rope handle with force. (Fig. 41)
16
CAUTION:
rope until it stops. Do not let go of the
starter rope when it is fully extended.
Release the starter rope slowly. If you do
not obey these instructions, it can cause
damage to the engine.
Note:
Do not pull the throttle trigger when you start
the engine.
8. Continue to pull the starter rope handle until the
engine starts or tries to start (pull max 3 times).
9. If the engine starts or tries to start, push the choke
control down. (Fig. 42)
10. Continue to pull until the engine starts.
Note:
Do not let the product stay running. Do the
next two steps immediately.
11. Hold the rear handle with your right hand and the
front handle with your left hand.
12. Immediately pull the front hand guard rearward in the
direction of the front handle to disengage the chain
brake. (Fig. 21)
Note:
The chain will move.
13. Run 20-30 seconds at elevated idle speed.
14. Pull the throttle trigger lightly to set normal idle.
15. Run 20-30 seconds at normal idle.
16. Use the product.
To start a warm engine
1. Move the front hand guard forward to engage the
chain brake. (Fig. 39)
2. Pull the choke control out and up.
3. Push the air purge bulb 6 times. (Fig. 40)
4. Push the choke control down. (Fig. 42)
5. Hold the body of the product on the ground with your
left hand.
6. Put your right foot through the rear handle.
7. Pull the starter rope handle slowly with your right
hand until you feel some resistance.
8. Pull the starter rope handle with force. (Fig. 41)
CAUTION:
rope until it stops. Do not let go of the
starter rope when it is fully extended.
Release the starter rope slowly. If you do
not obey these instructions, it can cause
damage to the engine.
Note:
Do not pull the throttle trigger when you start
the engine.
Do not pull the starter
Do not pull the starter
862 - 005 - 26.07.2023