Publicidad
Idiomas disponibles
Idiomas disponibles
English
Weight Capacity
CAUTION: To reduce the risk of injury, do not
overload the D
WALT power tool holster shelf
e
and cabinet.
Do not hang more than 100lbs (45kg) on each DWST82822
Do not hang more than 200lbs (90kg) on each DWST82824
when installed on D
WALT metal rail .
e
Do not hang more than 500lbs (227kg) on each DWST82824
when installed directly to wall studs, concrete or masonry.
DWST82822 Assembly and Installation
(Fig. A—E)
WARNING: Failure to comply with installation
may result in personal injury, product or
property damage.
Required Tools and Hardware
You will need to gather a few common tools and hardware.
Always consult your local building code for proper hardware.
D
WALT METAl RAil MOUnTing insTAllATiOn
e
•
Safety glasses
•
Gloves
•
Screwdriver
•
3/8" (10mm) wrench
•
7/16" (11mm) wrench
•
5/32" (4mm) hex wrench
•
Washers
14
•
1/4-20 x .0750 Socket head screws
•
Nuts
13
•
Spacer blocks
17
OPTiOnAl WAll MOUnTing insTAllATiOn
•
Safety glasses
•
Gloves
•
3/8" (10mm) wrench
•
#14x 3" screws
10
•
Washers
14
‑
Use masonry screws (not supplied) for mounting to
masonry block or a concrete wall.
Use the included #14x 3" screws
‑
wood studs.
CAUTION: Always use the correct screws for the
surface that D
WALT power tool holster will be
e
anchored in. Using the wrong screw will reduce the
holding force required for proper installation possibly
resulting in personal injury or property damage.
Decide how you would like to install your DWST82822 power
tool holster
1
before you begin.
1. DWST82822 power tool holster
wood framed, masonry, or concrete wall. See Installing
onto Wall Mounting, or Masonry/Concrete Walls to
install on those surfaces.
nOTE: The DWST82822 power tool holster
be installed over drywall and metal studs.
6
11
for mounting to
10
1
can be installed on a
1
may also
WARNING: Before attempting to attach D
power tool holster to metal studs and drywall
consult your local authority having jurisdiction
"AHJ" for proper fastening requirements.
Improper installation can cause personal injury and or
property damage.
D
WALT Metal Rail Mounting (Fig. B—D)
e
1. Slide the power tool shelf 2 over the power tool
holster 1 engaging the lances 3 into the lance slots 4
in the power tool shelf 2 .
nOTE: Ensure that all six lances
in the lance slots
4
.
2. Secure the shelf assembly
bracket
using four 1/4-20 x .0750 socket head screw
15
11
, four washers
14
Torque the hardware to 15 in/lbs.
3. After assembly is complete place top mat
power tool shelf
2
.
4. Remove the paper backing from the two spacer
blocks
17
. Install the two spacer blocks
sticky side to the back of the cabinet
nOTE: Spacer blocks
corners of the cabinet, approximately 1" (25mm) from
the edges.
5. Mount the shelf assembly to a D
so the metal rail mounting bracket
shown in Fig. D.
Wall Mounting (Fig. B, E)
1. Slide the power tool shelf 2 over the power tool
holster 1 engaging the lances 3 into the lance slots 4
in the power tool shelf 2 .
nOTE: Ensure that all six lances
in the lance slots
4
.
2. Locate and mark wall studs
3. Drill two 1/8" pilot holes.
nOTE: Use outside screw holes
24" (609 mm) on center. Use inside screw holes
mounting to studs 16" (406 mm) on center.
4. Position the DWST82822 shelf assembly
wall and straighten it using a level.
5. Place a washer
14
on each #14x 3" screw
the screws through the screw holes
6. Drive the #14x 3" screws
and into the wall studs
7. After assembly is complete place top mat
power tool shelf
2
.
Masonry/Concrete Walls
Prior to installing DWST82822 shelf assembly
assembly
18
on a masonry or concrete wall, waterproof the
surface to prevent moisture.
DO nOT attempt to install the DWST82822 shelf
assembly
18
using any type of masonry nail. Use #10 or
4.8 mm pan or washer head masonry screws (not included).
1. Slide the power tool shelf 2 over the power tool
holster 1 engaging the lances 3 into the lance slots 4
in the power tool shelf 2 .
3
are completely seated
18
to the metal rail mounting
and four nuts
13
as shown in Fig. C.
16
17
5
.
17
should be located on the lower
WALT metal rail
e
15
engages as
3
are completely seated
19
if installing over drywall.
20
for mounting to studs
18
onto the
10
and insert
20
as shown in Fig. E.
through the screw holes
10
19
until snug.
16
18
WALT
e
in the
with the
21
for
20
in the
shelf
Publicidad
