Descargar Imprimir esta página

GoodHome Blyth Manual Del Usuario página 2

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 10
Safety
EN
Care & Maintenance
EN
EN Safety
• Where possible drill between tiles in the grout.
• Failure to follow these instructions may result
in personal injury, damage to the product and
property damage.
• Never twist or kink the hose or otherwise restrict
the water ow whilst in use.
Getting started
• Make sure you have all of the parts listed.
• Make sure you have all of the tools required.
• This tap must be installed by a suitably
competent person.
• For domestic use only.
• It is important that supply pipes ar
before connecting the tap to ensure no pipe or
plumbing debris enters the tap.
CAUTION: Do not overtight
as this may damage the product.
• Take special care when installing exible
supply hoses. Tighten by hand only and do not
overtighten. Never twist or fold the exible pipe
during tting as this may damage or weaken the
pipe causing leaks.
• Ensure that the product is properly installed
before using.
• When the installation is complete, turn the water
supply on and check for leaks at all connection
points.
• TURN OFF WATER MAINS SUPPLY. The mains
stopcock is usually situated where the supply
enters the building.
• It is also recommended that the water heating
arrangements are turned off.
• Operating Speci cation:
Hot Water Supply - Maximum. 85 °C
Recommended 55-65 °C
• Operating Pressure:
Maximum 5 Bar
• If you are in any doubt about installing this
product, consult a technically competent
installer.
• When water pressure is higher than 5 bar a
pressure reducing valve (not supplied) must be
tted before the mixer.
• This product must be connected to a water
supply in accordance with the Water Supply
(Water Fittings) Regulations 1999, and UK Building
Regulations. If you are in any doubt about these
Getting started
EN
requirements, contact a quali ed plumber, your
local Water Company or the Water Regulations
Advisory Service (WRAS).
Pull out and spring neck taps
• Warning from your Water Supplier.
Care & Maintenance
• Use warm soapy water and a soft damp cloth to
clean the surface of the product. Wipe dry with a
clean cloth.
• Never use any solvents, scourers, abrasives,
bleach, acids, strong detergents, aggressive
chemical cleaners or solvent-type cleaning
solutions on the product.
• Periodically che
shed
ensure there are no leaks.
• Flexible supply hoses are tted with mesh
damaging the tap. Over time these may become
blocked, reducing the ow from the tap. If this
occurs, turn off the water supply to the tap,
disconnect the exible hoses and clean the
Guarantee
This product is under warranty for 5 years as from
the date of purchase, for normal, non-professional
household use. The warranty shall only apply upon
presentation of the till receipt or the invoice. Keep
your proof of purchase in a safe place.
The warranty applies to domestic use only. The
warranty covers product replacement or repair if
a manufacturing fault is found during the warranty
period, which begins on the date of purchase.
The warranty covers product breakdowns and
malfunctions under the condition that the product
is used in accordance with its intended use
and subject to installation and maintenance in
accordance with good practice and the information
contained in the user's manual.
This product must be installed so that it may be
later removed without damaging it.
This contractual warranty does not cover defects
and damage caused by thenatural wear of parts,
discoloration caused by light, bad weather, ooding,
heat releases, freezing, damage caused by water
quality (hardness, aggressiveness, corrosion, etc.),
by the presence of foreign bodies transported by
water or otherwise (sand, lings, etc.) or the lack
of room ventilation, and damages that could be the
consequence of improper use, misuse, negligence,
accident or maintenance that is defective or does
Pull out and spring neck taps
EN
Guarantee
EN
lters to prevent debris from your water supply
lters.
01
and connections to

Publicidad

loading