Metal Cutting - DeWalt DCS334 Manual De Instrucciones

English
the wood while cutting. Don't force the tool; let the blade
cut at its own speed. When the cut is complete, turn the jig
saw off. Let blade come to a complete stop and then lay the
saw aside before loosening the work.

Metal Cutting

In cutting thin gauge sheet metals, it is best to clamp wood
to the bottom of sheet metal; this will insure a clean cut
without the risk of vibration or tearing of metal. Always
remember to use a finer blade for ferrous metals (for those
that have a high iron content); and use a coarser blade for
non-ferrous metals (those that do not have an iron content).
Use a high speed setting for cutting soft metals (aluminum,
copper, brass, mild steel, galvanized pipe, conduit, sheet
metal, etc.). Use lower speed to cut plastics, tile, laminate,
hard metals, and cast iron.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
12
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made
or attempted by others. THIS LIMITED WARRANTY IS
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
by our:
D WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first year
WALT
after purchase.
e
2 YEARs FREE sERViCE On DEWAlT BATTERY PACKs
DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,
3 YEARs FREE sERViCE On DEWAlT BATTERY PACKs
DCB200, DCB204, DCB204BT, DCB203, DCB205, DCB205BT,
WALT Industrial
e
nOTE: Battery warranty voided if the battery pack is
tampered with in any way. D
for any injury caused by tampering and may prosecute
warranty fraud to the fullest extent permitted by law.
If you are not completely satisfied with the performance of
your D
can return it within 90 days from the date of purchase with
WALT factory
e
a receipt for a full refund – no questions asked.
WALT tools are covered
e
1 YEAR FREE sERViCE
DCB127, DCB201, DCB203BT, DCB207, DCB361
DCB206, DCB230, DCB606, DCB609
WALT is not responsible
e
90 DAY MOnEY BACK gUARAnTEE
WALT Power Tool, Laser, or Nailer for any reason, you
e
WALT (1-800-
e