DOMPEL NOMAD Manual De Instruccion página 4

location of installation
Install your Dompel product in a level place with no grooves or splices, preventing
rocking and vibration. The location must be airy and it must not allow straight sun-
light and it must be away from sources of heat (stoves, ovens, etc.) and flammable
products. Do not install your product outdoors.
cleaning and maintenance
Do not use metal spatulas, brushes and cleaning agents such as alcohol, acetone, kerosene, gasoline, bleach, thinner,
solvents, varsol, vinegar or other chemicals or abrasives such as sand paper or steel brushes.
To easily clean it, use a solution of warm water with a neutral soap and then wipe dry carefully. If chemical products reach
the upholstery, clean as soon as possible, preventing the products from staining or drying the fabric. The plastic parts
cannot be washed with boiling water. Chromed metal components can be cleaned with a soft, dry flannel, and silicone-ba-
sedautomotivewaxcanbeusedtoincreaseglossanddurability, in this case perform the task following the wax manufacturer's
instructions. Perform periodic cleaning, accumulated dust affects the beauty of the product making it difficult to clean the
product.
INSTALLATION AND ASSEMBLY
Remove all volumes from inside the package and follow these steps:
1
IMPORTANT: DO NOT REMOVE THE PROTECTION FROM THE BASE UNTIL THE END OF THE PRODUCT ASSEMBLY, IN
ORDER TO PROTECT THE CHROME FINISHING FROM POSSIBLE FALLING OF SCREWS OR TIGHTENING WRENCHES.
2
Round base: Remove the 04 sets M6 washer/nuts (H)
pre-fixed in the hydraulic, after fitting the hydraulic (F) on
the base (J) and finish the assembly by tightening the
nuts/washers, using a spanner 10mm.
IMPORTANT: AFTER FINISHING THE ASSEMBLY, ADJUST THE LEVELING FEET (N) UNTIL THE CHAIR IS FIRMLY
SUPPORTED ON THE FLOOR. DO NOT REMOVE THE BASE PROTECTION UNTIL THE END OF THE PRODUCT ASSEMBLY
IN ORDER TO PROTECT THE CHROME FINISHING FROM POSSIBLE FALLING SCREWS OR TIGHTENING WRENCHES.
3
5
7
8
Assemble the footrest (C) on the bottom of the seat (A).
Fasten the 02 screws (M6 x 35-SX) (E) pre-fixed on the
seat (A), use spanner 10.
Fit the handle (G) to the
hydraulic pump (F). Pay
attention to the correct
assembly position
described on the label
attached to the pump.
Fasten by tightening the
side screws
(M8 x 8-SX INT-SC) using
an Allen key (4 mm)
Assemble the base / hydraulic set
(F) on the recline system set or
fixed support (K), fixing the
washer set (M10) and upper
screw (M10 x 60-SX) (I), use
a spanner 17. IMPORTANT:
tighten the screw firmly before
proceeding to the next step of
assembly.
Assemble the seat
set (A) on the recline
system (K), fixing
the 06 screws
(M6 x 30-SX) (L)
pre-fixed on the seat
(A), use a spanner
10.
ENGLISH
1.1
2.1
Square base: Assemble the hydraulic (F) on the base (J)
using a washer set (M10) and lower fastening screw
(M10 x 25-SX) (H). Tighten it with a 17 open-end wrench.
Note: In the square base version, align the handle with
one of the sides of the base as shown in the arrow below,
preserving better aesthetics for the product.
4
6
9
Attach the headrest (D) manually to the backrest
support (B).
security
Avoid accidents. After
unpacking the product,
keep all the pack material
out of children's reach.
Square base pump: fit
the handle (G) to the
hydraulic pump (F). Pay
attention to the correct
assembly position
described on the label
attached to the pump.
Secure by tightening the
side screws (M8 x 8-SX
INT-SC) with a 4 mm
Allen key.
Manually fit the
finishing (plastic) cover
(M) on the backrest
support of the recline
system - or fixed
support (K).
Position the handle
guide for assembling
on the seat (align the
hole with the seat
thread) and fix the 02
screws (M6 x 30-SX)
(L) pre-fixed on the
seat (A), using a
spanner 10.
Assembe the backrest (B) on the
recline system (K): partially insert the
04 backrest screws (M6 x 30-AB) (E)
pre-fixed on the part, using a 4mm
Allen key. IMPORTANT: Check the
perfect horizontal alignment of the
backrest in relation to the seat be-
fore permanently fixing the screws
(final tightening).