Orbit 67790-24 rD Manual De Instrucciones

4-in-1 Drip Irrigation
Valve Instructions
2
6
1
For outdoor use with cold water only.
Check local codes for installation requirements.
If static water pressure exceeds 80 PSI, a pressure regulator
should be installed on the main sprinkler line.
Warning: DO NOT use pipe dope on threads, use thread seal tape.
1. Attaching the Valves
Apply thread seal tape generously on both male threaded ends and hand
tighten the Drip Tubing Adapter on the male threaded outlet (note the
arrow for water flow direction). The use of a union at the inlet of each valve
will allow for easy valve maintenance. Install a 1" female threaded PVC
adapter on the inlet side and connect it to the water source (see fig. 1).
Important: Do not over-tighten or use pipe joint compound.
2. Attaching Drip Tubing
Slide tubing into adapter until 1" of the tubing is
inserted in the fitting (see figure 2).
Note: The drip tubing adapter fits 1/2" distribution tubing from .630 OD to .710 OD.
3. Running the Wire
With the power off, connect the valves to an Orbit
or a residential standard 24-volt sprinkler timer. Use a multicolored,
multistrand jacketed sprinkler wire. Be sure the wire has at least one
more strand than the number of valves in the manifold. Trench and run the
wire to the valves. It is recommended, in areas that you will be frequently
digging, that you use a section of PVC pipe as a protective covering.
4. Wiring the Valve(s)
Attach a colored wire to one valve wire on the solenoid and a common
wire to the other wire on the solenoid. It doesn't matter which
solenoid wire you use as the common. Attach the colored wires to the
corresponding zone terminal in the timer and the common wire to
the common connection in the timer. Use standard sprinkler wire (20
gauge) for distances less than 800 feet and 18 gauge wire for over 800
feet. Use an Orbit Grease Cap and Wire Nut at each valve connection
®
(see figure 3). Also waterproof any splices made along the run.
Orbit
®
1.801.299.5555
orbitonline.com
DATE: 08/28/2023
DESIGNER: SM MARKETING: AP
ARTWORK №: 67790-24 rD
SOFTWARE: Adobe Indesign CC
4
3
5
7
Important Guidelines
Installation Instructions
sprinkler timer
®
K
Dieline
PMS
0000
Folded
L:
W:
H:
Key Features
1" Threaded Inlet—Connects to water source
1
Bleed Lever—Manually turns valve on and off
2
200 Mesh Filter—Ideal filtering for drip systems
3
Flush Port—Flushes debris from filter
4
1/2" Drip Tubing Adapter—Fits 1/2" (.630-.710) Drip Tubing
5
Jar-Top Lids—Easy to service valve and filter
6
30 PSI Internal Pressure Regulator
7
Pressure test all water lines and electrically test all timer
connections before covering pipe and timer control wire.
Place the manifold so that water drains away from the house.
Protect the 4-in-1 Valve with an valve box and place
gravel under the valves for drainage.
Flow indicator
Inlet
Use thread seal tape
Removing Drip Tubing
Dims./
Callout Fold
PMS PMS
0000 0000
Flat Additional Information
∙ Should be printed as 3 double
W:
008.500"
sided sheets, stapled in the
corner
H: 011.000"
∙
∙
∙
Outlet
Figure 1
Inserting Drip Tubing
Figure 2
Printers are responsible
for meeting print
Product
production requirements.
Coverage
Glue
Any changes must be
approved by Orbit
PRINTERS ARE
REQUIRED TO MATCH
Printed piece must meet
PMS
ALL SPECIFIED
0000 designated specifications
PMS COLORS.
on this form.
© 2015 Orbit Inc.
This work is the property
of Orbit , and cannot
®
be used, reproduced or
distributed in any way
without their express
permission.
.
®