Metabo SSD 18 LT 200 BL Instrucciones De Manejo página 7

Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
SYMBOLS
V ............ volts
....... direct current
n rated speed
0 ...............
../min ...... revolutions per minute
rpm ......... revolutions per minute
4. Overview
See page 2.
1 Square attachment for 1/2" tools *
2 Hexagon socket attachment for hexagon
screwdriving bits*
3 Locking sleeve*
4 Rotation selector switch / Transporting safety
device
5 Trigger
6 Handle (gripping surface)
7 LED light
For working in badly lit areas. The LED light
lights up when the machine is switched on.
8 Button for speed and tightening torque
selection
9 Battery pack *
10 Battery pack release button
11 Capacity indicator button *
12 Capacity and signal indicator *
13 Belt hook (attach as shown) *
* depending on the features / model
5. Initial Operation/Setting
Remove the battery pack from the machine
before any adjustment or maintenance is
carried out. Make sure that the tool is switched off
before fitting the battery pack.
5.1 Battery pack
Charge the battery pack (9) before use. Recharge
the battery pack if performance diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Li-Ion battery packs "Li-Power, LiHD" have a
capacity and signal indicator (12):
- Press the button (11), the LEDs indicate the
charge level.
- The battery pack is almost empty and must be
recharged if one LED is flashing.
Removing:
Press the battery pack release button (10) and pull
the battery pack (9) forwards.
Inserting:
Slide in the battery pack (9) until it engages.
5.2 Setting the direction of rotation,
engaging the transporting safety device
(switch-on lock)
Only operate the rotation selector switch /
transporting safety device (4) when the motor
is at standstill!
Actuate the rotation selector switch / Engage the
transportation lock (4).
R = Clockwise setting
(drive in screws)
L = Anti-clockwise setting
(undo screws)
0 = middle position: transportation safety device
(Switch-on lock) set
5.3 Switching on and off
Switching on: press the trigger switch (5).
Switching off: Release the trigger (5).
5.4 Speed / tightening torque
The speed and tightening torque are connected
directly. The lower the speed, the lower the
tightening torque.
The tightening torque is influenced in two ways:
1) Select maximum tightening torque.
You can select one of three tightening torque
settings by pressing the button (8). The maximum
tightening torques can be found in the table on
page 3 (M , M , M ).
1 2 3
The lights indicate which setting is selected.
1 = min. tightening torque
2 = medium tightening torque
3 = max. tightening torque
2) Stepless adjustment of the tightening torque:
The speed and tightening torque can be adjusted
steplessly in any torque setting by pressing the
trigger (5) firmly or lightly, thus adapting to working
conditions.
Recommendation: determine the correct setting
by carrying out trial screwdriving.
5.5 Changing SSD screwdriving bits
Inserting screwdriving bit: Slide locking sleeve
(3) forward and insert screwdriving bit as far as the
stop. Release locking sleeve (3) .
Pull on the screwdriver bit to check that it is
correctly seated.
Removing screwdriving bit: Slide locking sleeve
(3) forward and remove screwdriving bit.
Only use screwdriving bits with such plug-in
ends:
ENGLISH en
7