Rubi DC-250 PYTHON Manual Del Usuario página 4

EN
suitable for cutting all types of manmade and natural tile.
Its advanced water system eliminates most of the dust particles produced
by the cut.
such as non-through and L-cuts for electrical boxes or heat registers, easily.
With the power, innovation, and versatility, our Rubi premium features make
this the right tool to handle any tile cutting application.
ATTENTION! Read all safety warnings and all the instructions . Failure
to observe all the warnings and instructions indicated below could result in
Save all the warnings and instructions for future reference .
READ THE INSTRUCTION MANUAL
DO NOT EXPOSE TO RAIN OR MOISTURE
WEAR SAFETY GLASSES
WEAR HEARING PROTECTORS
WEAR PROTECTIVE GLOVES
WEAR A PROTECTIVE MASK
DO NOT TOUCH THE BLADE
PRECAUTION
1. KEEP GUARDS IN PLACE and in a good state of operation.
REMOVE BLADE WRENCH AND ADJUSTMENT TOOLS . Get used to
checking that blade wrench and adjustment tools are taken away from
the machine before starting it.
3. KEEP THE WORK AREA CLEAN . Untidy work areas and benches cause
accidents.
4. DO NOT USE IN HAZARDOUS ENVIRONMENTS
tools in damp or wet places or places that are exposed to the rain. Keep
the work area well lit.
KEEP AWAY FROM CHILDREN AND VISITORS . All visitors must use
safety glasses and stay a safe distance from the work area. Visitors
must not come into contact with the tool or extension cable while it is
in operation.
6. MAKE THE WORKSHOP CHILDPROOF by using padlocks, master
switches or removing the starting keys.
7. DO NOT FORCE THE TOOL.
speed for which it was designed.
8. USE THE TOOL CORRECTLY
- 4 -
TNO
9. USE THE APPROPRIATE EXTENSION CABLE . Ensure that your
thickness to carry the current that your product will use. A smaller cable
will cause a drop in voltage in the line, which will result in a loss of
the length of cable and the current. In case of doubt, use the thickest
WEAR SUITABLE CLOTHING
parts. Rubber gloves and non-slip footwear (boots with rubber soles)
are recommended when working in the open air. Also use a protective
cap to contain long hair.
11. ALWAYS USE SAFETY GLASSES WITH SIDE SHIELDS . Glasses for
WORK SAFELY . Use clips or clamps to hold the work whenever practical,
it is safer than using your hand and frees both hands to use the tool.
13. DO NOT OVERREACH . Maintain your posture and balance at all times.
14. MAINTAIN THE TOOLS WITH CARE . Keep tools sharp and clean for
better and safer performance. Follow the instructions for lubrication and
changing accessories.
DISCONNECT TOOLS . All tools should be disconnected when not in
use, before carrying out maintenance or changing accessories, wheels,
bits, blades, etc.
16. PREVENT ACCIDENTAL STARTUP
plugging in any tool.
17. USE RECOMMENDED ACCESSORIES . See the operating manual for
cause injury.
18. NEVER LEAN ON THE TOOL
tips over or the cutting tool starts up accidentally.
19. CHECK FOR DAMAGED PARTS . Before using the tool, carefully check
to determine if a damaged guard or other part will operate correctly
and carry out its intended function. Check the alignment of the moving
parts, connections of the moving parts, as well as for any broken parts,
A guard or other part that is damaged must be properly repaired or
personal injury.
USE THE CORRECT FEED DIRECTION . Insert the part to be cut to the
blade or cutter only against the rotation direction of the blade or cutter.
NEVER LEAVE THE TOOL UNSUPERVISED WHILE IN OPERATION.
TURN OFF THE POWER SUPPLY
completely stopped.
1. ALL GROUNDED, CORD-CONNECTED TOOLS :
In the event of a malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electric
into a matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Improper connection of the equipment-grounding conductor can result
surface that is green with or without yellow stripes is the equipment-
grounding conductor. If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment- grounding conductor
to a live terminal.
instructions are not completely understood, or if in doubt as to whether
the tool is properly grounded.
Repair or replace damaged or worn cord immediately.
2. GROUNDED, CORD-CONNECTED TOOLS INTENDED FOR USE ON A
SUPPLY CIRCUIT HAVING A NOMINAL RATING LESS THAN 150 V:
that looks like the plug illustrated in Sketch A. A temporary adapter,
which looks like the adapter illustrated in Sketches B and C, may be
should be used only until a properly grounded outlet can be installed
extending from the adapter must be connected to a permanent ground
such as a properly grounded outlet box.
3. GROUNDED, CORD-CONNECTED TOOLS INTENDED FOR USE ON
250 V, INCLUSIVE: