Metabo W 21-230 Instrucciones De Manejo página 6

02 ENG_9790_0205
ENGLISH
3.2 Double insulated tools are equipped with
a polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any
way. Double insulation
the three-wire grounded power cord and grounded
power supply system.
Applicable only to Class II (double insulated) tools.
3.3 Avoid body contact with grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
3.4 Don't expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
3.5 Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Replace damaged
cords immediately. Damaged cords increase the
risk of electric shock.
3.6 When operating a power tool outside,
use an outdoor extension cord marked
"W-A" or "W". These cords are rated for outdoor
use and reduce the risk of electric shock.
4 Personal Safety
4.1 Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use tool while tired or under the
influence of drugs, alcohol or medication. A
moment of inattention when operating power tools
may result in serious personal injury.
4.2 Dress properly. Do not wear loose clothing
or jewelry. Contain long hair. Keep your hair,
clothing and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught
in moving parts.
4.3 Avoid accidental starting. Be sure switch
is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that
have the switch on invites accidents.
4.4 Remove adjusting keys or wrenches
before turning the tool on. A wrench or a key
that is left attached to a rotating part of the tool
may result in personal injury.
4.5 Do not overreach. Keep proper footing and
balance at all times. Proper footing and balance
enable better control of the tool in unexpected
situations.
4.6 Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety shoes,
hard hat or hearing protection must be used for
appropriate conditions.
6
18.12.2007 13:31 Uhr
eliminates the need for
Seite 6
5. Tool Use and Care
5.1 Use clamps or other practical way to
secure and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
5.2 Do not force tool. Use the correct tool for
your application. The correct tool will do the job
better and safer at the rate for which it is
designed.
5.3 Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
5.4 Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the risk
of starting the tool accidentally.
5.5 Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
5.6 Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained tools
with sharp cutting edges are less likely to bind and
are easier to control.
5.7 Check for misalignment or binding of
moving parts, breakage of parts, and any other
condition that may affect the tool's operation.
If damaged, have the tool serviced before
using. Many accidents are caused by poorly
maintained tools.
5.8 Use only accessories that are
recommended by the manufacturer for your
model. Accessories that may be suitable for one
tool may become hazardous when used on
another tool.
6 SERVICE
6.1 Tool service must be performed only by
qualified repair personnel. Service or
maintenance performed by unqualified personnel
could result in a risk of injury.
6.2 When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.
4 Specific Safety Rules
Always use proper guard with grinding wheel.
A guard protects operator from broken wheel
fragments.
Accessories must be rated for at least the
speed recommended on the tool warning label.
Wheels and other accessories running over rated