IKRA KES 1800-35 Instrucciones De Manejo página 22

When proper precautions are taken the operator will
be able to control the power of a kickback. Never let
go of the chain saw!
• Avoid unusual postures and do not cut above
shoulder height. This avoids accidentally touching
objects with the tip of the bar and allows for a better
control of the chain saw in unexpected situations.
• Only use the replacement bars and chains pre-
scribed by the manufacturer. The use of wrong
replacement bars and chains may lead to chain
breaks or kickbacks.
• Adhere to the manufacturer's instructions to
sharpen and maintain the chain. Depth limiters that
are too low increase the risk of a kickback.
• Set the loop so that it is not detected during op-
eration of branches or the like.
9) Important instructions for your personal safety
a) General safety instructions
1. Never attempt to use an incomplete machine or one
which an unauthorised alteration has been imple-
mented.
2. These devices are not designed to be operated by
persons who have insufficient experience and/or
insufficient knowledge or by persons with impaired
physical, sensory or mental capabilities, unless they
are being supervised by a person who is responsible
for their safety or they are receiving instructions
about how these devices are to be used.
3. Children and young persons under 18 may not
operate electrical chainsaws, with the exception of
apprentices older than 16 under the supervision of
a trained adult.
4. The chainsaw may only be used by persons who
have sufficient experience.
5. Always keep these Operating Instructions together
with the chainsaw.
6. Only lend or give this chainsaw to persons who are
familiar with its use. Also give them these Operating
Instructions.
B) Instructions on using the chain saw safely
7. Attention! Read the Operating Instructions care-fully
and have yourself instructed in the use of a chain saw
before you use it for the first time.
8. Always store your electric tools in a safe place.
Electric tools not being used should be stored in a
dry, inaccessible or locked place, outside the reach
of children.
9. Check the extension cable regularly and replace it if
it gets worn or damaged.
10. Check the power cable for damage or cracks every
time before you use it. Damaged cables must be
replaced.
11. Always hold the chain saw with both hands while
working with it.
12. The chain saw must be disconnected from the power
supply before you tighten the chain, exchange the
chain or carry out any other work on the saw. - With-
draw the plug!
13. During work breaks put the machine down in such a
manner that nobody is at risk.
14. When switching on the chain saw, ensure that it is
supported well and hold it firmly. The chain and bar
must be free.
15. Withdraw the plug immediately if the power cable is
damaged or cut.
16. The chain saw may only be connected to socket
outlets with earthing contact and tested electrical
installations. We recommend the use of a residual-
current-operated circuit-breaker. The fuse must have
a value of 16 A and mustn't be used by other con-
sumers while working with the chain saw.
17. The cable must be winded off completely when you
use a cable drum.
18. Ensure that the power cable has no kinks and is not
damaged.
19. The chain saw may only be used in a completely as-
sembled state. No protective devices may be missing.
20. Switch the chain saw off immediately if you notice
any changes in the machine.
21. Always have a first-aid kit fulfilling DIN 13164 at
hand in case of accidents.
22. If the chain saw comes into contact with earth, stones,
nails or other foreign objects, withdraw the plug im-
mediately and check the chain as well as the bar.
23. Ensure that no chain oil penetrates into the earth or
sewage. Always place the chain saw on something
that will absorb any oil dripping from the bar or chain.
24. Avoid to use the trimmer in poor weather conditions,
especially if there is a risk of a thunderstorm.
C) Warning to the danger of recoil ("kickback")
25. If possible, use a stand.
26. Always keep an eye on the bar tip.
27. Only place a running saw on the object to be cut.
Never start the machine while the chain rests on
something.
28. So called piercing cuts with the bar tip may only be
carried out by trained personnel.
D) Instructions on safe working techniques
29. Working on ladders, scaffoldings or trees is for-
bidden.
30. Ensure that the wood cannot twist while it is being
cut.
31. Watch out for splintering wood. While you are saw-
ing you may be injured by flying wood chips.
32. Do not use the chain saw to lever or move the wood.
33. Only cut with the lower section of the saw. The saw
will be repulsed towards you if you try and cut with
the upper section of the saw.
34. Ensure that the wood is free of stones, nails or other
foreign objects.
35. We recommend that first-time users are instructed
practically as to the correct use of the chainsaw and
the required personal safety equipment by an expe-
rienced operator; the cutting of round wood or logs
should be trained on a log stand or similar rack-type
device first.
36.Keep the running chainsaw from touching the ground
or wire fences.
GB-5