Jata JVVP3145 Instrucciones De Uso página 10

ASSEMBLING INSTRUCTIONS
• Place by pressing the plastic cover (12) over the base (3).
• Remove the "L" screw from the extensible tube (10) and insert the extensive tube into the base, after that
you can tight the "L" screw.
• Loose the nut to fix the height, remove the extensible tube (10) and fix it.
• Insert the head (6) to the extensible tube and fix it by tighten the nut.
• Unscrew the nut to fix the propeller (8) clockwise and the grid nut (7) anticlockwise.
• Place the rear grid (4) into the motor shaft and fix it with the screw grid by turning it clockwise.
• Place the blade (1) into the shaft by pressing till the end and screw the guard cap (8) into the shaft
anticlockwise.
• Insert the frontal grid (5) and close the fixing grids (9) making coincide the grids with its rails and adjust
with the screw.
INSTRUCTIONS OF USE
• Remember the fan always must be placed on a flat and stable surface.
• Plug the appliance into the mains.
• To adjust the height, loose the screw (11), place the fan into the desired height and fit the screw.
• Move the air flow by moving up and down the head till getting the desired position.
• Control knobs (2)
- On / off button (a).
- Speed regulator (b).
- Modo: intermittent speed function (c).
- Timer (d).
- Automatic oscillation (e).
- Natural mode (f).
- Speed indicator (g).
- Indicator time (h).
- Night mode (i).
• Switch on the fan by pushing the button (a) and adjust the speed to (low-medium- high) by pressing the
regulator (b).
• To turn the head, push the oscillation button (e).
• To get an intermittent function push the mode button (c).
- Fix mode – Choose the desired speed (minimum- medium- maximum) with the regulator (b).
- Night mode – Press the button (c) till the symbol (i) is light on and choose the desired program (g) with
the speed regulator (b). (See the chart 1).
- Speed III – Cycles of 30 seconds with a maximum – medium – low intermittent speed for 30 minutes.
Next, the light "II" will be on and will start cycles of 30 seconds with medium-low intermittent speed
and to finish, the light "I" will light on and will start cycles of 5 seconds with a low intermittent
speed till you switch off the appliance.
- Speed II - Cycles of 30 seconds with a maximum – medium – low intermittent speed for 30 minutes
and to finish, the light "I" will light on and will start cycles of 5 seconds with a low intermittent
speed till you switch off the appliance.
- Speed I – There are cycles of 5 seconds with low intermittent speed till you switch off the appliance.
- Natural mode – press the (c) button till the symbol (f) is light on and choose the desired program (g)
according to the chart 1 with the speed regulator (b). At this moment, the selected program will keep
fixed till the fan is switched off.
• To program the fan, press the timer (d) till selecting the desired hours (maximum 7:30 hours).
• You can control the fan with the remote control (13), maximum functioning distance 20 m.
MAINTENANCE AND CLEANING
• Before you proceed to cleaning, make sure the appliance is unplugged from the mains.
• Clean with a slightly damp cloth.
• It is important to keep the frontal grid and the back grid clean of dust.
• You can disassemble the blades for cleaning by following the assembling reverse process.
• Do not use abrasive or chemical products, such as metallic scourers, which may deteriorate the surfaces
of the appliance.
ENVIRONMENT PROTECTION
• Dispose the appliance according to the local garbage regulations.
• Never throw it away to the rubbish. So you will help to the improvement of the environment.
10