Publicidad
Idiomas disponibles
Idiomas disponibles
LAWN
MOWER
Always
observe
safety
rules when
per-
forming
any maintenance.
TIRES
• Keep tires free of gasoline,
oil, or insect
control chemicals
which can harm rubber.
• Avoid stumps,
stones,
deep ruts, sharp
objects
and other
hazards
that may
cause
tire damage.
DRIVE WHEELS
Check
rear drive wheels
each time you
mow to be sure they move freely.
The
wheels
not turning
freely
means
trash,
grass cuttings,
etc., may be inside
the
drive wheel
and dust cover area and must
be cleaned
out to free drive wheels.
If necessary
to clean the drive wheels,
check
both rear wheels.
BLADE
CARE
For best results,
mower
blade must be kept
sharp.
Replace
a bent or damaged
blade.
TO REMOVE
BLADE
1.
Disconnect
spark
plug wire from spark
plug and place wire where
it cannot
come in contact
with plug.
2.
Turn lawn mower
on its side. Make
sure air filter and carburetor
are up.
3.
Use a wood
block between
blade and
mower
housing
to prevent
blade from
turning
when removing
blade bolt.
NOTE:
Protect
your hands with gloves
and/or
wrap blade with heavy cloth.
4.
Remove
blade bolt by turning
counter-
clockwise.
5.
Remove
blade and attaching
hardware
(bolt, lock washer,
hardened
washer).
NOTE:
Remove
the blade adapter
and
check the key inside
hub of blade adapter.
The key must be in good condition
to work
properly.
Replace
adapter
if damaged.
TO REPLACE
BLADE
1.
Position
the blade adapter
on the en-
gine crankshaft.
Be sure key in adapter
and crankshaft
keyway
are aligned.
2.
Position
blade on the blade adapter
aligning
the two (2) holes in the blade
with the raised
lugs on the adapter.
3.
Be sure the trailing
edge of blade (oppo-
site sharp
edge) is up toward the engine.
4.
Install the blade bolt with the lock
washer
and hardened
washer
into
blade adapter
and crankshaft.
5.
Use block of wood between
blade and
lawn mower
housing
and tighten
the
blade bolt, turning
clockwise.
• The recommended
tightening
torque
is
35-40 ft. Ibs.
IMPORTANT:
Blade bolt is heat treated.
If bolt needs
replacing,
replace
only with
approved
bolt shown
in the Repair
Parts
section
of this manual.
Blade adapter.
Key .......
Lockwasher
Blade
/
/
/
/
/
Crankshaft
keyway
Blade
bolt
\
washer
Crank
sha_
/
\
Trailing edge
Blade adapter
TO SHARPEN
BLADE
NOTE:
We do not recommend
sharpening
blade - but if you do, be sure the blade
is balanced.
An unbalanced
blade will
cause eventual
damage
to lawn mower
or
engine.
• The blade can be sharpened
with a file
or on a grinding
wheel.
Do not attempt
to sharpen
while on the mower.
• To check
blade balance,
drive a nail into
a beam or wall. Leave about one inch of
the straight
nail exposed.
Place center
hole of blade over the head of the nail.
If blade is balanced,
it should
remain
in
a horizontal
position.
If either
end of the
blade moves downward,
sharpen
the
heavy end until the blade is balanced.
GRASS
CATCHER
• The grass catcher
may be hosed
with
water,
but must be dry when
used.
• Check
your grass catcher
often for dam-
age or deterioration.
Through
normal
use it will wear.
If catcher
needs
replac-
ing, replace
only with approved
replace-
ment catcher
shown
in the Repair
Parts
section
of this manual.
Give the lawn
mower
model
number
when
ordering.
GEAR
CASE
• To keep your drive system
working
properly,
the gear case and area around
the drive should
be kept clean and free
of trash build-up.
Clean
under the drive
cover twice a season.
• The gear case is filled with lubricant
to the
proper
level at the factory.
The only time
the lubricant
needs
attention
is if service
has been performed
on the gear case.
• If lubricant
is required,
use only Texaco
Starplex
Premium
1 Grease,
Part No.
750369.
Do not substitute.
13
Publicidad
