GE 20" Wide Manual De Instrucciones página 4

ELi REPLACE THE WIRE COVER
Replace wire cover on range back by sliding its left edge under the retaining tabs and replace the
screws removed earlier. Make sure that no wires are pinched between (:over and range back.
Back ofrange Back ofrange
95 screws to
remove wire
(:over
Screw to
remove
terminal
block (:over
Terminal
block (:over
E_ ANTI-TIP DEVICE INSTALLATION
Tip-Over Hazard
A child or adult ca n tip the range and be killed.
Install the anti-tip bracket to the wall or floor.
Engage the ra nge to the anti-tip bracket by sliding the
ra nge back such that the foot is engaged.
Re-engage the anti-tip bracket if the range is moved.
Failure to do so can result in death or serious burns
to children or adults.
To reduce the risk of tipping the range, the
range must be secured by a properly irrstalled
arrti-tip bracket. See installation irrstructiorrs
shipped with the bracket for complete details
before attempting to irrstall.
To check if the bracket is installed and
engaged properly, look underneath the range
to see that the rear leveling leg is engaged
in the bracket. On some models, the storage
drawer or kick panel can be removed for
easier inspection. If visual inspection is not
possible, slide the range forward, confirm the anti-tip bracket is securely attached to the floor or wall, and
slide the range back so the leveling leg is under the anti-tip bracket. If the range is pulled from the wall for
any reason, always repeat this procedure to verify the range is properly secured by the anti-tip bracket.
Never completely remove the leveling legs or the range will not be secured to the anti-tip bracket.
r.=A=_
LEVELTHERANGE
AWARNI NG:
Never cornpletely remove the leveling leg
as the range will not be secured to the anti-tip device properly.
MODELS WITHSTORAGE D RAWER ORKICK PANELS
D
@
E1
r6]
Plug in unit and slide into place. Pull drawer out until it stops.
Lift front of drawer until the stops (:lear the guide. Remove the drawer.
Install the oven shelves in the oven and position the range where
it will be installed.
Check for levelness by placing a spirit level on one of the oven shelves.
Take two readings-with the level placed diagonally first
in one direction and then the other,
rE1 The front leveling legs can be acJjusted from the bottom
and the rear legs can be acJjusted from the top or the bottom.
El Use an acJjustable wrench to adjust the leveling legs until
the range is level.
[_] LEVELTHE RANGE(CONT.)
r_ Position cord so that it does not interfere with drawer.
Place drawer rail on guides. Push the drawer in until it stops.
r_ Lift front of drawer and push in until the stops (:lear
the guides.
rT1 Lower the front of the drawer and push in until it (:loses.
MODELS WITH BAKING, W ARMINGDRAWERS OR DOUBLE OVEN
[]
rgl
El
F61
rT1
rT1
FO-1
range
Plug in the unit.
Measure the height of your countertop at the rear of the opening (X).
AcJjust two rear leveling legs so that the rear of cooktop is at the same height
as the counter (Y).
Slide unit into place.
Install oven shelves in the oven and position the range where it will be installed.
Check for levelness by placing a spirit level on one of the oven shelves.
Take two readings-with the level placed diagonally first in one direction
and then the other.
Adjust front leveling legs until the range is level.
I1UI FINAL INSTALLATION CHECKLIST
. Check to make sure the circuit breaker is closed (RESET)or the circuit fuses are replaced.
* Be sure power is in service to the building.
* Check that all packing materials arrd tape have been removed. This will irrclude tape on metal panel under
corrtrol knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic. Failure to remove
these materials could result in damage to the appliance once the appliance has been turned on arrd
surfaces have heated.
* Check that the door arrd drawer are parallel to each other arrd that both operate smoothly. If they
do not, see the Owner's Manual for proper replacement.
* Check to make sure that the rear leveling leg is fully irrserted irrto the Anti-Tip bracket arrd that the bracket
is securely irrstalled.
OPERATION CHECKLIST
. Turn on one of the surface units to observe that the element glows within 60 seconds. Turn the unit
off when glow is detected. If the glow is not detected within the time limit, recheck the range wiring
connections. If change is required, retest again. If no change is required, have building wiring checked for
proper corrnections arrd voltage.
* Check that the Clock (on models so equipped) display is energized. If a series of horizontal red
lines appear in the display, disconnect power immediately. Recheck the range wiring connections.
If change is made to connections, retest again. If no change is required, have building wiring checked for
proper connections and voltage. It is recommended that the clock be changed if the red lines appear.
* Be sure all range corrtrols are in the OFF position before leaving the range.