BOMANN EK 6021 CB Manual De Instrucciones página 22

The Timer
The appliance including heating can be time-controlled via
the timer. Prerequisite for the correct operation of the timer
is the setting of the current time and day of the week.
• You can set a maximum of 23 hours and 50 minutes in
advance.
• The time setting is done in 10-minute increments.
• You may program up to 10 different timer settings.
• Each timer setting includes its own switch-on time,
switch-off time and temperature setting.
• A setting can be programmed for any day of the week or
for several days.
• If you want, you may only program a switch-off time dur-
ing operation and ignore the entry of the switch-on time.
If the switch-off time is meant to be the next day, remem-
ber to adjust the day of the week when programming.
• Even if the appliance is disconnected from the mains,
the timer settings will be preserved.
Display Timer Settings
1. Press the TIMER SET button. The number for the first
setting flashes in the display and "ON" lights up.
2. Press the or button to display the switch-on times of
the 10 timer settings.
3. Press the button in order to switch to the switch-off
time. "OFF" will appear on the display.
4. Use the or button to display the switch-off times.
5. To clear a displayed setting, press the C button.
Programming the Timer
NOTE:
If you have accidentally made a wrong selection during
timer programming, exit the menu by pressing the OK
button and start again.
1. Select setting number
1) Press the TIMER SET button. The display of the
timer setting number starts flashing.
2) Use the or button to select another setting
number.
3) Press the TIMER SET button again to confirm the
selection.
2. Weekday(s) selection
1) The arrow and a weekday will be flashing. Use the
or button to select a weekday.
2) Press the button to activate the weekday. The
arrow beside the weekday is flashing.
3) Press the TIMER SET button to confirm the selection.
4) If you want to deactivate a weekday, press the
button, while the arrow
flashing.
22
EK6021CB_IM
beside the weekday is
3. Setting the start time
("ON" will light up in the display)
1) The hour display starts flashing.
Use the or button to set the hour.
2) Press the TIMER SET button to confirm the selection.
3) The minute display starts flashing.
Use the or button to set the minute.
4) Press the TIMER SET button to confirm the selection.
4. Setting the switch-off time
("OFF" will light up in the display)
1) The hour display starts flashing.
Use the or button to set the hour.
2) Press the TIMER SET button to confirm the selection.
3) The minute display starts flashing.
Use the or button to set the minute.
4) Press the TIMER SET button to confirm the selection.
5. Setting the base temperature for the heating
NOTE:
For technical reasons, the current weekday is dis-
played again in this menu item.
1) The temperature display starts flashing. Use the or
button to set the base temperature for the heater.
2) Press the TIMER SET button to confirm the selection.
Activating / Deactivating the Timer
IMPORTANT NOTE:
• In the event of a power failure, all timer settings will be
preserved. However, the appliance will be reset to the
basic settings.
• For safety reasons, the heating will be switched off.
WARNING: Fire hazard!
• Before switching on the timer, check the settings of
the current weekday, the current time and the timer
settings.
• Always set the start time in such a way that the appli-
ance is under proper supervision during operation.
1. Use the 900 W / 1800 W button to set the desired heating
power. Alternatively, you may also use the IC button to
select the adaptive start control function of the heater.
2. Use the DIMMER button to set the intensity of the
flames you wish to have at the start time.
3. If you want the lighting to additionally switch on at the
start time, select it now with the BACK-LIGHT button.
4. By using the TIMER ON / OFF button you switch the
timer on or off.
NOTE:
• If the timer is activated, the
the display.
• In addition, the display will show the symbols for the
intensity of the flames and for the heating, provided
this it has been switched on.
symbol will appear in
02.08.18