Weller Zero Smog TL Traducción Del Manual Original página 18

GB
ENGLISH
WARNING Fire and explosion hazard!
The unit is not permitted to be used for the extraction of
in昀氀ammable gases.
The unit must not be exposed to temperatures above
50°C, naked 昀氀ame or condensed solvents.
The organisation operating the unit is responsible for the
observance of the legal limits for noxious substances at
the place of work.
The 昀椀ltration system may only be put into operation if it is
in perfect working order.
Intended use of the soldering station/ desoldering
station also includes the requirement that you
adhere to these instructions,
„
observe all other accompanying documents,
„
comply with national accident prevention guidelines
„
applicable at the place of use..
The manufacturer will not be liable for unauthorised
modi昀椀cations to the device.
User groups
Due to differing degrees of risk and potential hazards, sever-
al work steps may only be performed by trained experts.
Work step
Installation of complex
pipe systems with
multiple extractor arms
connected
Replacing electrical repla-
cement parts
Speci昀椀cation of mainte-
nance intervals
Operation
Filter change
Operation
Notice
The unit may emit dust from the main 昀椀lter after trans-
portation. Make sure that the unit is put into service in
a suitable room.
CAUTION A high noxious gas concentration will
cause the activated charcoal to heat up.
To avoid overheating, the unit should be run without
noxious gases for several minutes before switching off.
Put the tool into operation as described in the chapter
„Placing into operation".
Please adhere to the operating instructions of the
connected devices.
Check to see if the mains voltage matches the ratings
on the nameplate.
16
User groups
Specialist personnel with
technical training
Technical trainees under the
guidance and supervision of
a trained expert
Electricians
Technical trainees under the
guidance and supervision of
a trained expert
Safety expert
Non-specialists
Make sure the machine is switched off before plugging
in.
Optimal gas 昀椀ltration is achieved as follows:
Temperature of process air in gas 昀椀lter < 38 °C
Relative humidity < 60 %
Gas molecules > 30 g/mol (better 昀椀ltration results are
achieved with larger molecules)
Boiling point of the gas molecules > 0 °C
Care and maintenance
WARNING
Before doing any work on the machine, pull the
plug out of the socket.
The unit must not be altered or modi昀椀ed in any way!
Repairs must always be referred to a Weller-trained
specialist.
Use original replacement parts only.
Filter change
To ensure that the 昀椀ltration system
MIN 1x
functions properly, the compact 昀椀lter
must be replaced as follows
at least once a year or
„
year
if the maximum allowable
„
workplace concentration is exceeded
or
„
as per maintenance schedule
Notice
Different 昀氀uxes and 昀氀ux constituents and the amount of
and size of dust particles in the extracted air will signi昀椀
cantly effect the 昀椀lters working life. Submicron particles
in the extracted air increase when soldering or welding
to varnish insulated wire.
The suspended matter 昀椀lter and the broadband gas
昀椀lter are complementary to one another and can be
replaced together as a compact 昀椀lter. The compact
昀椀lter must be changed once a year in order to ensure
it is fully functional. The 昀椀ne dust 昀椀lter (昀椀lter mat) is the
preliminary stage of the compact 昀椀lter and therefore
must be replaced more frequently.
It is strongly recommended that the compact 昀椀lter be
replaced after no more than 10 昀椀ne dust 昀椀lter changes.
An alarm sounds and the yellow warning light 昀氀a-
shes: Recommended service life of 昀椀lter has expired.
(see Operating time 昀椀lter display/Extraction capacity
昀椀lter display)
An alarm sounds and the red warning light is lit
continuously: Extraction capacity is too low. Switch
off the 昀椀lter unit. Check the nozzles, tubes and ext-
ractor arms, and clean them if necessary. If the alarm