I
CE
V-BELTS
TO CHANGE ENGINE OIL
Check V-belts for deterioration and wear after every 50
hours of operation and replace if necessary. The belts
are not adjustable. Replace belts if they begin to slip from
wear. (See "TO REMOVE BELT COVER" in the Service
and Adjustments section of this manual).
The V-belts on your snow thrower are ofspecial construction
and should be replaced by original equipment manufacturer
(OEM) belts available from your nearest dealer. Using other
than OEM belts can cause personal injury or damage to
the snow thrower.
AUGER GEAR CASE
The gear case was filled with lubricant to the proper
level at the factory. The only time the lubricant needs
attention is if service has been performed on the gear
case.
•
If lubricant is required, use only Ronex ED #1 grease.
TRACTION DRIVE SYSTEM
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
CAUTION: Any lubricating
of the above compo-
nents can cause contamination
of the friction
wheel and damage to the drive system of your
snow thrower.
ENGINE
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG-SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAE ViSCOSiTY
GRADES
I
I
°F
-20
0
30
32
40
°C
-3'0
-2'0
-10
0
10
TEMPERATURE RANGE ANTICIPATED
BEFORE NEXT OiL CHANGE
NOTE:
Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F/0°C.
Check your engine oil level more frequently to
avoid possible engine damage from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the snow thrower is not used for 25 hours
in one year.
Checkthe crankcase oil level before starting the engine and
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.
Determine temperature
range anticipated before next oil
change. All oil must meet API service classification SG-SL.
•
Be sure snow thrower is on level surface.
•
Oil will drain more freely when warm.
•
Catch oil in a suitable container.
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and place-
ment of a suitable container. The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See "TO REMOVE WHEELS"
in the Service and Adjustments section of this manual).
1.
Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2.
Clean area around drain plug.
3.
Remove drain plug and drain oil in a suitable container.
4.
Install drain plug and tighten securely.
5.
Wipe off any spilled oil from snow thrower and engine.
6.
Install leftwheel (if removed for draining oil). Besureto
install klick pin into proper hole in wheel axle (See "TO
REMOVE WHEELS" in the Service and Adjustments
section of this manual).
7.
Remove oil fill cap!dipstick. Be careful not to allow dirt
to enter the engine.
8.
Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate
capacity see
"PRODUCT SPECIFICATIONS"section
ofthis manual.
9.
Use gauge on oil fill cap!dipstick for checking level.
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at "FULl" line on dipstick.
10. Wipe off any spilled oil.
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and!or damage.
SPARK PLUG
Replace spark plug atthe beginning of each season or after
every 100 hours of operation, whichever occurs first. Spark
plug type and gap setting are shown in the "PRODUCT
SPECIFICATIONS"
section of this manual.
CLEANING
IMPORTANT:
For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.
WARNING: Disconnectsparkplugwire
from spark plug and place wire where it
cannot come in contact with plug.
e
e
Keep finished surfaces!wheels free of gasoline, oil, etc.
We do not recommend using a garden hose to clean
your snowthrower unless the electrical system, muffler
and carburetor are covered to keep water out. Water
in engine can result in shortened engine life.
16