Simpson Strong-Tie Quik Drive T-QDPROINSNA23 Instrucciones De Operación página 2

PARTS - SCHEMATIC - COMPONENTS
Attachment
Extension Mandrel
G2 Locking Lever
Depth Adjustment Wheel
Bit Release Key
Using the correct driving bit is necessary.
The bit(s) included in each box of Quik Drive
Variations in materials and driving technique can cause excessive wear. Additional bit packs are available for purchase.
Reference the description on the bit sticker in your box of screws or the screw box label to ensure correct selection.
Quik Drive systems utilize 10 recess drive types and sizes.
Drive Type / Size Bit
#2 square drive BIT2S
#2U (Undersized) BIT2SU
#3 square drive BIT3S
#3U (Undersized) BIT3SU
BIT2P
#2 Phillips
BIT3P
#3 Phillips
BITHEXLB14
1/4" drive
BITHEXLB516
5/16" drive
BITTX20-PL
T20 6-lobe
BITTX25
T25 6-lobe
BITTX30
T30 6-lobe
TROUBLESHOOTING GUIDE
Quik Drive tools are easy to use. As with any power tool, there are a few basic things to remember.
PROBLEM
Screws won't drive.
They spin for a second, then fall over
on their side. Little or no penetration.
Screws won't drive completely.
They go down about halfway,
then the bit spins out.
Screws won't drive completely.
They are almost completely driven but
won't countersink completely.
Screws don't advance properly
causing tool to jam.
Extension
inside extension
Handle
Nose Piece
Feed Pawl Lever
(Must be engaged in Feed
Pawl Assembly Slot)
screws should drive the entire box.
®
for most screws with #2 recess and interior grade coating
for most screws with #2 recess; exterior grade coating and stainless steel
for most screws with #3 recess and interior grade coating
for most screws with #3 recess; exterior grade coating and stainless steel
for all Quik Drive screws with Phillips recess
for all Quik Drive screws with 1/4" hex head
for all Quik Drive screws with 5/16" hex head
for Quik Drive systems with T20 6-lobe drive
for Quik Drive systems with T25 6-lobe drive
for Quik Drive systems with T30 6-lobe drive
SOLUTION
Make sure the screwgun is not in reverse.
Check to be sure you are using the correct bit for the type of screws you are driving.
Check for bit wear. It may be time to install a new bit.
Push harder when driving.
Check the depth adjustment on the attachment. Reset if necessary.
You may have missed the substrate.
Example: In flooring, this will occur if you miss the joist.
Use only Quik Drive brand collated screws.
Be sure the screw strip is inserted correctly - pointed end first.
Lift the tool completely off the work surface after driving each screw.
Don't drag screw strips on the work surface as you move to the next position.
Be sure the feed pawl assembly is intact and feed lever is engaged.
For further assistance, call 800-999-5099
Screwdriver Motor
Mandrel
Part #:
BPHX516G2 QDPROHX516G2
BPHXLBPPG2 QDPROPP150G2
PMANDREL10 QDPROPP150G2
Guide Tube
PMANDREL65 QDPRO200G2,
QDPROLDHG2,QDPROPHG2
PMANDREL75 QDPRO200SG2,
QDPRO300SG2, QDPRORFG2,
QDPRO300SRFG2, QDHSD60, QDHSD75
BPHXLBSDG2 QDPROSDX150G2
Feed Pawl
Assembly
Bit
Bit Release Slot
inside attachment
Non-Skid Teeth
part # 150187
(QDPRO200SG2,
QDPRO250G2,
QDPRO300SG2)
Use with or without the
"stand-up" extension