Publicidad
Idiomas disponibles
Idiomas disponibles
TRACTOR
Always observe safety' rules when performing
any maintenance.
BRAKE
OPERATION
if tractor
requires
more than five (5) feet to
stop at highest
speed
in highest
gear on a
level, dry concrete
or paved surface,
then
brake must be serviced_
(See 'qrO CHECK
BRAKE"
in the Service
and Adjustments
section
of this manual).
TIRES
• Maintain
proper
air pressure
in all tires
(See PSI on tires).
,
Keep tires free of gasoline,
oil, or insect
control
chemicals
which
can harm rub-
ber.
• Avoid
stumps,
stones,
deep ruts, sharp
objects and other hazards that may cause
tire damage,
NOTE:
To seal tire punctures
and prevent
flat tires due to slow leaks, tire sealant may
be purchased
from your local parts dealer.
Tire sealant
also prevents
tire dry rot and
corrosion.
OPERATOR
PRESENCE
SYSTEM
AND
REVERSE
OPERATION
SYSTEM
(ROS)
Be sure
operator
presence
and
reverse
operation
systems
are working
properly,
if
your tractor does not function
as described,
repair the problem
immediately.
• The engine
should
not start unless
the
brake
pedal
is fully depressed,
and the
attachment
clutch
control is in the disen-
gaged position°
CHECK
OPERATOR
PRESENCE
SYSTEM
• When the engine
is running,
any attempt
by the operator
to leave the seat without
first setting the parking
brake should shut
off the engine.
• When
the engine
is running
and the at-
tachment
clutch is engaged,
any attempt
by the operator
to leave the seat should
shut off the engine.
° The attachment
clutch should never oper-
ate unless the operator
is in the seat.
ROS "ON" Position
Engine "ON" Position
(Normal Operating)
CHECK
REVERSE
OPERATION
(ROS)
SYSTEM
• When the engine is running with the ignition
switch in the engine "ON" position and the
attachment
clutch engaged,
any attempt
by the operator
to shift into reverse should
shut off the engine.
• Whenthe
engine is runningwith
the ignition
switch in the ROS "ON" position
and the
attachment
clutch engaged,
any attempt
by the operator to shift into reverse should
NOT shut off the engine.
BLADE
CARE
For best results mower blades must be sharp_
eplace worn, bent or damaged
blades.
CAUTION:
Use only a replacement
blade
approved
by the manufacturer
of your tractor.
Using a blade not approved
by the manu-
facturer
of your tractor
is hazardous,
could
damage your tractor and void your warranty.
BLADE
REMOVAL
1. Raise mowerto
highest position to allow
access to blades.
NOTE: Protect your hands with gloves and/
or wrap blade with heavy cloth.
2.
Remove
blade bolt by turning
counter-
clockwise.
3.
installnewbladewithstamped"THiSSIDE
UP" facing deck and mandrel
assembly_
IMPORTANT:
To ensure
proper
assembly,
center hole in blade must align with star on
mandrel
assembly.
4.
Install
and tighten
blade
bolt securely
(45-55 Ft. Lbs. torque).
IMPORTANT:
Special
blade
bolt
is heat
treated.
Mandrel
Assembly
Blade
BATTERY
Center Hole
-,,_i_.
Your tractor
has a battery
charging
system
which is sufficient
for normal use, However,
periodic
charging
of the battery
with an au.-
tomotive
charger
will extend its life.
, Keep battery
and terminals
clean.
• Keep battery
bolts tight.
• Keep small vent holes open.
° Recharge
at 6-10 amperes
for 1 hour,
NOTE:
The original
equipment
battery
on
your tractor
is maintenance
free.
Do not
attempt to open or remove caps or covers,
Adding
or checking
level of electrolyte
is
not necessary.
22
Publicidad
