Grounding Instructions - Makita GB602 Manual De Instrucciones

■ DIRECTION OF FEED. Be aware of wheel rotation
direction; never grind without the work rest being
properly set. NEVER grind more than one workpiece at
a time.
■ DISCONNECT TOOLS before servicing; when
changing accessories such as blades, bits, cutters, and
the like.
■ REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in off position before
plugging in.
■ VOLTAGE WARNING: Before connecting the tool to a
power source (receptacle, outlet, etc.) be sure the
voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage
greater than that specified for the tool can result in
SERIOUS INJURY to the user- as well as damage to
Table 1: Minimum gage for cord
Ampere Rating
More Than Not More Than
0
6
10
12
000173

■ GROUNDING INSTRUCTIONS:

This tool should be grounded while in use to protect the
operator from electric shock. The tool is equipped with
a three-conductor cord and three-prong grounding type
plug to fit the proper grounding type receptacle. The
green (or green and yellow) conductor in the cord is the
grounding wire. Never connect the green (or green and
yellow) wire to a live terminal. Your unit is for use on
120 volts and has a plug that looks like Fig. "A".
1
1. Grounding Blade
2. Cover of Grounded Outlet Box
000088
■ Do not modify the plug provided – if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
■ Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
■ If repair or replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding
conductor to a live terminal.
Volts
120 V
6
10
12
16
2
the appliance. If in doubt, DO NOT PLUG IN THE
APPLIANCE. Using a power source with voltage less
than the nameplate rating is harmful to the motor. USE
PROPER EXTENSION CORD. Use only three-wire
extension cords that have three-prong grounding-type
plugs and three-pole receptacles that accept the tool's
plug. Make sure your extension cord is in good
condition. Replace or repair damaged or worn cord
immediately. When using an extension cord, be sure to
use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and
overheating. Table 1 shows the correct size to use
depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
Total length of cord in feet
25 ft. 50 ft.
AWG
18 16
18 16
16 16
14 12
■ Check with a qualified electrician or service personnel
if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is
properly grounded.
■ Repair or replace damaged or worn cord immediately.
WARNING:
Wheel coasts after turn off.
■ CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that
is damage must be properly repaired or replaced by an
authorized service center to avoid risk of personal
injury.
■ KEEP TOOL DRY, CLEAN, AND FREE FROM OIL
AND GREASE. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any solvents to clean tool.
■ INSPECT POWER SUPPLY AND EXTENSION
CORDS periodically and, if damaged, have repaired by
a qualified service technician. Stay constantly aware of
cord location and keep it well away from the rotating
wheel.
■ NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor or sparking from grinding
metal could ignite fumes.
100 ft. 150 ft.
16 14
14 12
14 12
Not Recommended
3