Publicidad
Idiomas disponibles
Idiomas disponibles
Auto mode: 7-Day timer program
In Auto mode, the thermostat automatically switches over between Comfort mode and Economy mode as per the
programmed schedule. You may set the schedule for one or more days.
1)
Press the set button until
2)
Press + and – to scroll through the days of the week. Mon(1) – Sun (7)
3)
To select the day(s) you wish to program the schedule for, press the
number. To skip days, continue to scroll with the + button until the end of the week. This process allows you
to program similar week days at the same time. Once the specific day(s) are selected, press
You can select Comfort or Economy mode in every 15 minutes interval of the day. The 0:00 to 24:00 hour time bar
allows you to set the mode throughout the selected day(s).
4)
To set the time period of a certain mode, press mode to switch between Comfort
5)
Press set to set 15 min by 15 min for the above chosen mode. On the time bar, a solid black bar
represents the state is in Economy mode. (The + and – buttons move the bar but does not set).
6)
Once the time is set, press ok to confirm. The screen displays the remaining days that still need to be set.
Press set to continue program the rest otherwise press ok skips to step 8.
7)
Repeat steps 2...6 until all days are set.
8)
At the end of the Timer program
(mode button) to cancel adjustments.
Note: The setting will continue to be in effect until changed.
Once the settings are saved, the changeover between the operating modes happens automatically when
turned on.
By factory default, the time program has default settings as follows:
Day(s)
Mon (1) - Fri (5)
Sat (6) - Sun (7)
Holiday mode setting
In the Holiday mode, you may set the thermostat to run at a constant temperature setpoint during your absent days.
1)
To activate the holiday mode, press the
2)
Press + or – to adjust the temperature setpoint for Holiday mode. Press
3)
Next press + or – to adjust the number of days that you are out for holiday (Note: 0 = Holiday Mode Off).
ok
4)
Press
to confirm.
5)
Once the holiday is activated, the countdown of remaining days is shown on the screen.
*Note: Holiday mode can be aborted at any time by pressing esc.
Change of Batteries
The thermostat uses two
alkaline batteries type AAA.
Once the batteries are inserted
in the battery compartment, all
symbols appear on the display
for about 3 seconds.
is displayed when the
battery is low. Please replace
the old ones with two new type
AAA alkaline batteries.
Control Parameters
If you want to change control parameters, proceed as follows:
+, -, mode
1)
Press
2)
Select the required parameter by pressing + or –.
ok
3)
Press button
. The current value of the selected parameter starts blinking.
4)
The value can be changed by pressing + or –.
ok
5)
Press button
If you wish to adjust additional parameters, repeat steps 2 to 5, or press
Parameter list
Parameter no.
P01
P06
P08
P09
P10
Wireless pairing
1)
Turn on receiver and wait for 5 seconds for initialization. Press the Learn button to enter learning mode. The
LED blinks in red and green alternately.
2)
Turn on main unit and press
3)
Press "+" to select parameter "P08". The default the value of P08 is "OFF".
4)
Press OK key and then press
5)
Press OK key again to confirm the setting. "rFL" and "EArn" are displayed on screen indicating the pairing is
starting. If the pairing is done successfully, the main unit exits the pairing mode automatically. The LED on the
receiver turns green continuously.
Note:
Always press the Learn button on the receiver before pairing with the main unit.
Issued by
Siemens Switzerland Ltd
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
Tel. +41 58 724 2424
www.siemens.com/buildingtechnologies
A6V13156975_en--_a
2/2
is selected to activate the 7-day Timer Program. Press ok to confirm.
represents the state is in Comfort mode whereas a non-solid black bar
and
Comfort mode
7:00 -9:00 hr and 17:00 -22:00 hr
7:00 -22:00 hr
set
simultaneously for at least 5 seconds. Release them and, the display shows P01.
to confirm the adjusted value, or
Parameter name
Sensor calibration
Periodic pump run
RF learning
Reload factory setting
(Reset)
Software version
mode
and "+" and "
-
+
or
key to switch the value to "ON".
Technical specifications and availability subject to change without notice.
A5W00231888A_AA
esc
appears to finalize the settings. Press ok to confirm or "esc"
button until
is selected, then press
Characteristics
Batteries
Setpoint Range Switching
Capacity of Relay
Voltage
Current
Norms and standards
esc
to cancel the changes.
Default value
0 º C
OFF
OFF
OFF
Display software version
number only
-
" key simultaneously to enter the parameter setting mode.
set
button, and the dot freezes under the
or Economy mode
Economy mode
22:00 -7:00 hr and 9:00 -17:00 hr
22:00 -7:00 hr
ok
.
ok
to confirm.
esc
to leave parameter setting mode.
Setting range
-3.0 º C ~3.0 º C
(step:0.5 º C )
ON: Enable function;
OFF: Disable function
ON: Enable RF learning;
OFF: Disable RF learning
ON: Enable reload;
OFF: Disable reload;
No adjustment
© Siemens Switzerland Ltd, 2022
Siemens Smart Infrastructure
ok
to confirm.
.
is
2 x 1.5 V, AAA
4...35 °C
AC 24...250 V
0.1...5 (2) A
2022-03-29
Publicidad
