DeWalt DCE555 Manual De Instrucciones página 30

ENglIsh
Attaching a Dust Extractor to the Dust
Shroud (Fig. I)
The DCE555DC dust shroud (sold separately) is compatible
with the DWH161 DEWALT Universal Dust Extractor
(sold separately).
• Friction-fit the the dust shroud
of the DWH161 Universal Dust Extractor.
Belt Clip (Fig. E)

WARNING: To reduce the risk of serious personal injury,
ensure the screw holding the belt clip is secure.
IMpoRTaNT: When attaching or replacing the belt clip
use only the screw 12 that is provided. Be sure to securely
tighten screw.
If the belt clip is not desired at all, it can be removed from
the tool.
To remove the belt clip, remove the screw
belt clip in place.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. L)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NoTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
battery pack out of the tool handle. Insert it into
the charger as described in the charger section of
this manual.
Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.

WARNING: Tool may stall (if overloaded or improperly
used) causing a twist. Always expect the stall. Grip the
tool firmly with both hands to control the twisting
action and prevent loss of control which could cause
personal injury.
Proper hand position requires one hand on the handle
and the other bracing the battery to control the twisting
action of the tool.
28
14 port to the hose
11
12 that holds the
9 into the tool handle, align
10 and firmly pull the
On/off Button (Fig. A)
• To start the motor, press the on/off button
• To stop the motor, press the on/off button
LED Worklight (Fig. A)

CAUTION: Do not stare into the LED. Serious eye
18
injury could result.
When the tool is activated by pressing the on/off button
the LED worklight
worklight will turn off 20 seconds after the on/off button has
been used to turn the unit off.
,
To Maintain Safe Tool Control
• Make sure the work surface is free of nails or screws.
Cutting into a nail or screw may cause the tool to jump,
damaging the bit.
• Never operate the tool with one hand while holding
the workpiece with the other hand. Always clamp the
material and guide the tool with both hands.
• Do not cut material lying on a hard surface. Clearance
behind material to be cut must be allowed for
protruding bit.
• Disconnect battery from tool before making adjustments,
changing bits, or cleaning tool.
• Do not start the tool with bit engaged in the material.
The bit may grab the material.
Cutting a Hole for an Electrical Outlet
(Fig. G)

WARNING: Shut off all live electric circuits to any areas
where cut‑outs will be made.
1. Push any wiring deeply into the outlet box to avoid
damage from the cutting bit.
2. Before hanging the sheet covering the fixture box, mark
the approximate location of the center of the fixture
box on the wall board. Check the cutting bit depth
against the side of the board to be sure it will cut entirely
through the material.
3. Tack the sheet in place with a few fasteners avoiding the
stud holding the fixture box. This allows the wall board to
flex slightly around the protruding fixture box.
4. Turn the cut-out tool on. Holding the tool firmly with
both hands, plunge the bit straight into the center of the
fixture box.
5. Cut to the right until the bit reaches the inside edge of
the fixture box. Pull the bit out just enough it to clear the
edge of the fixture box. Plunge the bit in again, holding
the bit gently against the outside of the fixture box.
6. Follow the outside of the fixture box and complete the
cut counterclockwise, keeping slight pressure against the
fixture box. This will minimize wandering and give you a
clean, precise cut.
15
7. Remove the waste and dust from the fixture box. Finish
fastening the sheet of wall board.
8 will automatically turn on. The LED
1 .
1 again.
1 ,