Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
piece missing or in bad conditions, contact the official Technical Support Service of Cecotec
immediately.
Box contents:
-
SealVac 140 SteelCut vacuum sealer
-
Bag roll
Installation
-
Place the device on a flat, stable, and dry surface, away from any corrosive material, heat,
or moisture.
-
The plug must be easily accessible so that it can be unplugged quickly in case of emergency.
-
When not in use, store the appliance in a cool, dry place and keep it away from sunlight
and heat sources.
3. OPERATION
The bag's width must not exceed 30 cm. Otherwise, it will not fit. The bag must not be more
than 1.5 cm thick. Otherwise, the appliance may get damaged.
How to prepare a bag
1.
Plug the device to a power supply. The dry food sealing button's light indicator will turn
on. Open the lid by pressing the release button on both sides. Fig. 4
2.
If you have not already done so, place the bag roll into the bag roll cavity. Pull the end of
the bag until there are at least 20 cm between the sealing tape and the top of the bag as
shown in figure 5.
3.
Close the lid by pressing both of its sides until you hear a closing sound. Fig. 6
4.
Press the sealing button. The button's light indicator will light up.
5.
Once sealing is complete, the light indicator will turn off. Slide the cutting blade across
the roll to cut the bag off. Make sure the cutting blade is on the edge before cutting. Fig. 7
How to package food
1.
Insert the food you want to vacuum pack in the bag. You can use a ready-to-use bag or
you can make one as explained in the previous section.
2.
Place the edge of the bag in the vacuum chamber and leave at least 8 centimetres
between it and the bag's contents as shown in figure 8. For larger foods, you will need to
leave more space.
3.
Close the lid and press both of its sides until you hear a closing sound. Fig. 9
4.
Press the packing button for dry or wet food, depending on the type of food you want to
package (the corresponding light indicator will be on while in operation).
5.
Press the vacuum packing button for the bag to be automatically emptied and sealed.
22
SEALVAC 140 STEELCUT
Fig. 10
6.
After the bag is sealed (no light indicator should be on), open the lid by pressing the
opening buttons on both sides. Remove the bag. Fig. 11
7.
Wait 15 seconds before packing the next bag to allow the appliance to cool down.
How to seal bags without vacuum packing:
1.
Insert the food you want to package in the bag. You can use a ready-to-use bag or you can
make one as explained in the previous section.
2.
Place the edge of the bag in the vacuum chamber and leave at least 8 centimetres
between it and the bag's contents as shown in figure 8. For larger foods, you will need to
leave more space.
3.
Close the lid and press both of its sides until you hear a closing sound.
4.
Press the sealing button. The button's light indicator will light up. Fig. 12
5.
After the bag is sealed (no light indicator should be on), open the lid by pressing the
opening buttons on both sides. Remove the bag.
How to assemble and disassemble the cutting blades:
Disassembly
1.
Turn the blade cover counterclockwise by approximately 100°. Fig. 13
2.
Remove the cutting blade cover and the blade itself. Fig. 14
Assembly
Repeat the disassembly process in reverse:
1.
Assemble the blade and the cover. Fig. 15
2.
Turn the cover clockwise by approximately 100°. Fig. 16
Warning
After sealing 5 bags in a row, allow the device to cool down for about a minute. Do not use the
appliance while in cooldown.
How to seal jars
1.
Connect one end of a suction tube to the air suction hole and the other end to the jar
opening.
2.
Press the external sealing button so the device vacuums the air out. This function will
finish when the sound stops. You can stop sealing manually by pressing the button again.
Zip bag sealing
1.
Connect one end of a suction tube to the air suction hole and the other end to the bag's
opening.
2.
Press the external sealing button so the device vacuums the air out. This function will
finish when the sound stops. Stop the function manually just by pressing the button again.
ENGLISH
SEALVAC 140 STEELCUT
23
Publicidad
