Publicidad
Idiomas disponibles
Idiomas disponibles
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
WARNING
Follow the safety and charging instructions
and correct usage given in the instruction
manual of your 20V IXES Series battery and
charger.
A
detailed
charging process and further information are
provided in this separate manual.
6
Technical data
Rated voltage
Operating mode
Air pump output:
Displacement pump output:
Max. pressure
Max. speed
Blower air flow rate
Compressor air flow rate
USB-A port
USB-C port
Protection class
Subject to technical changes!
Operating mode S3 (periodic intermediate duty)
The operation consists of a nominal load and standstill
time.
The cycle time is 10 min, the relative duty cycle is 25% of
the cycle time.
Noise data
WARNING
Noise can have serious effects on your health. If the
machine noise exceeds 85 dB, please wear suitable
hearing protection for you and persons in the vicinity.
The noise and vibration values have been determined in
accordance with EN 62841-1.
Air pump
Sound pressure level
(at the operating station) L
Uncertainty K
Measured sound power level L
Uncertainty K
Guaranteed sound power level L
20 | GB
description
of
20 V
(Lithium-ion
battery)
12 V
230 V~
S3 20% 10 mins
120 W
80 W
10.3 Bar (150 PSI)
rpm
3500
(compressed air)
rpm
15000
(low pressure)
380 l/min
21 l/min
5V/2A
5V/2A
II/(Double insulation)
82.5 dB
pA
92.0 dB
wA
2.04 dB
94 dB
wA
www.scheppach.com
Blowing mode
Sound pressure level
(at the operating station) L
Uncertainty K
Measured sound power level L
Uncertainty K
Vibration parameters
Total vibration value a
Uncertainty K
the
The total vibration emission values specified and the de-
vice emissions values specified have been measured in
accordance with a standardised test procedure and can
be used for comparison of one electric tool with another.
The total noise emission values specified and the total vi-
bration emission values specified can also be used for an
initial estimation of the load.
WARNING
The noise emission values and vibration
emission value can vary from the specified
values during the actual use of the power
tool, depending on the type and the manner
in which the electric tool is used, and in par-
ticular the type of workpiece being pro-
cessed.
Try to keep the stress as low as possible. For example:
Limit working time. In doing so, all parts of the operating
cycle must be taken into account (such as times in
which the power tool is switched off or times in which it
is switched on, but is not running under a load).
If necessary, adhere to rest periods and limit the duration
of work to the bare minimum.
7
Unpacking
WARNING
The product and the packaging material are not
children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suffo-
cating!
• Open the packaging and carefully remove the product.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. Immediately report any damage to the trans-
port company that delivered the Product. Later claims
will not be recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
3 dB
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
pA
wA
<2.5 m/s
h
74.6 dB
3 dB
82.3 dB
3 dB
2
2
1.5 m/s
Publicidad
