Richell 803840 94352-6 Manual De Instrucciones

y | nstrucei
| Y Richell® Instruction Manual Manual de instrucciones JAN| 5044/5045
Manuel d' instruction 取扱 説明 書 使用 説明 書 취 급 설명서
Thank you for choosing Richell's Product. Please read this instruction manual carefully before using
this product, and keep for future reference. If you give this product to someone else, please also give
this instruction manual to the new owner. Please note some parts of the figures shown below may be
slightly different from the actual product, for your better understanding of the structure and proper use. ae isa
Applicable Model lr Expands er
e This Divider is designed exclusively designed for Richell's | ~ Crate Small
803840 94920-7, 803840 94921-4. ンマ '
Specifications Connecting Joint Connecting Joint
LA
UPC/JAN | 803840 94352-6 / 4973655 50441-3 803840 94353-3 / 4973655 50451-2 X + x
|
I
Dimensions | 20.7"W x 0.8"D x 22.6"H 28"W x 0.8"D x 26.4"H
Frame: Rubber wood (Lacquer finished) Joint: Polypropylene
Wire : Steel (Polyester coating)
What are the following signs? Divider (1) Joint (4)
The following signs are special remarks for safety use of the product. Keep these remarks in mind before using this product.
: Remarks on inappropriate use which might cause death, serious injury and/or physical damage.
: Remarks on inappropriate use which might cause slight injury and/or physical damage.
Instruction for Proper Use
| Warnings! |
WARNING! Choking Hazard;
Joint is a small part; Pets and Children can choke or suffocate on joints. Adult supervision is required; keep joints away from Pets and
Children during assembly. Discard broken joints at once.
e Do not use this product for anything other than its intended purpose.
e Do not use this product while your pet is leashed to avoid unexpected accidents.
e Make sure each part is properly fixed in place to avoid unexpected serious injury/damage to pets, and/or product; your pet could get caught between
the wires or between wire and wooden frame.
e Keep this product in sight and keep the Door open when unattended to avoid unexpected injury or death to your pet; pets behave unexpectedly when
startled by thunder, lightning, or by other animals.
@ Be careful of sharp objects when assembling or using this product.
Howioassenbleise This product is exclusively designed for Richell's 803840 94920-7, 803840 94921-4.
All of the following parts except Divider are sold separately.
Materials
How to attach Divider When assembling/disassembling this product, do not allow your pet to
remain in the Pen.
Place Divider at a desired position, aligning wires of Connecting Point and Front/Back Panels as shown
in the figure below and connect using the Joints. (Right side, Left side, Upside and Downside at 4 arrow points).
>< Divider cannot be attached to the part of Front Panel where Vertical Wire Slat of Back Panel
a wire panel is removed.
Divider cannot be attached to thick wires nor to the part to be
overlapped by Door when opening. x
※For UPC 803840 94353-3 (Medium), follow only the Di 'part
to connect as shown below. Back Panel
Front Panel A
ON
Vertical Wire Slat of
Front Panel B
How to lock/unlock Joints
①Place Small Convexes between
the wires.
@Fold Joint and snap to lock.
Small
Convexes
To unlock
place a coin in the
slit and turn it as
shown in the figure
on the right.
< š Connecting
Horizontal Wire Slat o
Point
Front Panel B
How to remove Wire Slat for
Divider
(Remove the Fixing Bolt on the top
of Divider.
@Loosen the Screw. Then, lift the
Top Frame. Top Frame
e The figure shows the
product with its Slide
Door to the front and
Divider attached.
Front Panel B ^
Connecting Point e To place Divider where Front and Back Panels
Vertical Wire Slat of Fron A overlap and the opening is narrower, place the
Divider diagonally in the Pen and the attach it
to the desired position one side at a time.
e If a Joint does not lock properly, try locking again
® Remove Wire re Bot
Slat of Divider. ュー OCTOW
Big Convexes after moving Divider from side to side. Do not try Wire Slat
;
;
Horizontal Wire Slat of
to force lock it as the Joint may be damaged.
of Divider
Connectng Pon
Front Panel B
e Insert Joint from the side of Big Convexes to clip
ATT
the wires. | ===>)
※Make sure to check that the Top/Bottom
e When removing the Screw competely from Divider, this product will fall apart to pieces. Make sure to and Front/Back of the Wire Slat is in the
stand up the Divider while attaching the Wire Slat. correct postion when reassembling.
How to clean olf you find something wrong with this product,
e Use a mild detergent and water and clean with a soft cloth/sponge. Cleaning with a scrub brush and/or please let us know. Thank you!
using a polishing powder may cause scratched, rust and/or discolor this product.
e When using creosol or other disinfectants, make sure to dilute them, otherwise For USA Customers
damage to the wooden finish or discoloration may occur.
e Do not use harsh chemicals such as thinner, benzene or alcohol as these may
cause damage/discoloration to the finish.
O After cleaning, wipe dry with soft cloth or place in a shaded area to air dry; do not
place this product in direct sunlight to avoid damage/discoloration to the finish.
OPlease note that product specifications and design may change without prior notice for the purpose of
quality improvement.
OThere may be coating cracks at some joints and each product may experience different coloration of the
wood grain as frames are made of natural wood. 4
Designed by:
Richell Corporation, Japan
Distributed by:
Richell USA, Inc.
Grand Prairie, Texas 75050
Phone (972) 641-9795 Fax (972) 641-8495
Visit us at www.richellusa.com
Made in China