Publicidad
Idiomas disponibles
Idiomas disponibles
the correct guard from your local dealer or authorized
service centre.
nOTE: Edge grinding and cutting can be performed with Type
27 wheels designed and specified for this purpose; 6.35 mm
thick wheels are designed for surface grinding while thinner
Type 27 wheels need to be examined for the manufacturer's
label to see if they can be used for surface grinding or only
edge grinding/cutting. A Type 1 guard must be used for any
wheel where surface grinding is forbidden. Cutting can also be
performed by using a Type 1 wheel and a Type 1 guard.
nOTE: See the Accessories Chart to select the proper guard /
accessory combination.
Adjusting and Mounting Guard (Fig. D, E)
CAUTION: Turn unit off and remove the battery pack from
the tool before making any adjustments or removing or
installing attachments or accessories.
CAUTION: BEFORE operating the tool, be sure to identify
which adjustment option your tool is set to.
adjustment Options
Your grinder offers one- and two-touch options for guard
adjustment.
One-touch: When the slanted side of the guard release
•
lever
10
is engaged, the guard can be easily repositioned by
rotation it clockwise. The lever does not need to be depressed
to turn the guard.
Two-touch: When the squared side of the guard release
•
lever
10
is engaged, the guard can be repositioned by
depressing the guard release lever and rotating the guard.
One Touch
setting Guard adjustment Options
To adjust the guard release lever
adjustment option:
1. Remove screw
14
using a T20 bit.
2. Remove the guard release lever. Choose the end of the
lever for the desired adjustment option. One-touch will
use the slanted end of the lever. Two-touch will use the
squared end.
3. Replace the lever, positioning the chosen end under the
spring
13
. Ensure the lever is in proper contact with
the spring
4. Replace screw.
Mounting Guard (Fig. D)
1. Press the guard release lever
2. While holding the guard release lever open, align the lugs
15
on the guard with the slots
3. Keeping the guard release lever open, push the guard down
until the guard lugs engage and rotate them in the groove
on the gear case hub. Release the guard release lever.
Two Touch
10
for desired
10
.
16
on the gear case.
4. With the spindle facing the operator, rotate the guard
clockwise into the desired working position. The guard body
should be positioned between the spindle and the operator
to provide maximum operator protection.
nOTE: The guard release lever should snap into one of the
alignment holes
on the guard collar. This ensures that
17
the guard is secure.
5. To remove the guard, follow steps 1–3 of these instructions
in reverse.
Flanges and Wheels
Mounting Non-Hubbed Wheels (Fig. F)
WARNING: Failure to properly seat the flange/ clamp nut/
wheel could result in serious injury (or damage to the tool
or wheel).
CAUTION: Included flanges must be used with depressed
centre Type 27 and Type 42 grinding wheels and Type 1
and Type 41 cutting wheels. See the accessories chart
for more information.
WARNING: A closed, two-sided cutting wheel guard is
re quired when using cutting wheels.
WARNING: Use of a damaged flange or guard or fail ure
to use proper flange and guard can re sult in injury due to
wheel breakage and wheel contact. See the accessories
chart for more information.
1. Place the tool on a table, guard up.
2. Install the unthreaded backing flange
the raised centre (pilot) facing the wheel.
3. Place wheel against the backing flange, centreing the wheel
on the raised centre (pilot) of the backing flange.
4. While depressing the spindle lock button and with the
hex depressions facing away from the wheel, thread the
clamp nut
8
on spindle so that the lugs engage the two
slots in the spindle.
5. While depressing the spindle lock button, tighten the
locking flange with a wrench.
6. To remove the wheel, depress the spindle lock button and
loosen the threaded locking flange with a wrench.
Mounting Sanding Backing Pads (Fig. A, F)
nOTE: Use of a guard with sanding discs that use backing pads,
often called fiber resin discs, is not required. Since a guard is
not required for these accessories, the guard may or may not fit
correctly if used.
WARNING: Failure to properly seat the flange/ clamp nut/
wheel could result in serious injury (or damage to the tool
or wheel).
WARNING: Proper guard must be reinstalled for grinding
wheel, cutting wheel, sanding flap disc, wire brush or
wire wheel applications after sanding applications are
complete.
1. Place or appropriately thread backing pad
the spindle.
2. Place the sanding disc
19
EnGLIsh
7
on spindle
4
18
on
on the backing pad
18
.
with
49
Publicidad
