cecotec CONGA POPSTAR 3000 CARPET CLEAN Manual De Instrucciones página 26

ENGLISH
Warning:
- To know the detergent quantity and use, carefully read the manufacturer instructions.
- Stop using the device when the water or foam in the waste-water tank (12) reaches the
maximum water level and clean the waste-water tank (12); otherwise, water may enter
the machine.
Using the right-angle suction nozzle
Press the suction nozzle against the soiled surface and move it from top to bottom. Fig. 15
5. CLEANING AND MAINTENANCE
Warning
- Stop the device and unplug it from the mains before cleaning it.
- Do not wet the device to avoid the risk of electric shock.
- Do not use detergents, thinners, benzene or other chemical agents to clean the device.
- After every use, you must remove and clean the waste-water tank (12), the clean-water
tank (3) and the suction nozzle (A/B) to prevent humidity and dirt remains from emitting
bad odours. Fig. 16
5.1 Cleaning the main body
- The most common dirt can be cleaned with a slightly damp cloth.
- The most stubborn dirt can be cleaned with a cloth slightly soaked in detergent and then
a cloth slightly soaked in water.
5.2 Cleaning the waste-water tank
When the waste water reaches the maximum level (11), stop using the device and unplug
1.
it from the mains.
2. Remove the waste-water tank (12). To do so, slide the waste-water tank release tab (13)
and remove the waste-water tank (12) in the direction of the arrow shown in Figure 17.
Remove the upper cover of the waste-water tank and empty the waste water. Fig. 18
3.
4. Clean the tank, the upper cover and the sealing strip. Fig. 19
5. Install the sealing ring in the cover and secure it to the tank, making sure the holes (29)
match the tabs (28). Fig. 20
Place the waste-water tank (12) in the main body of the device (4). Fig. 21
6.
Figure 20:
19. Tabs
20. Holes
50
Warning
- Do not lean or shake the waste-water tank when transporting or assembling it; otherwise,
waste water will easily leak.
- We recommend you empty the waste water before it exceeds the maximum level on the
tank (11); if you continue using the tank after the waste water has exceeded the maximum
water level (11), the float valve (31) will automatically stop the machine vacuuming water
(30). Fig. 23
Figure 22:
21. Automatic vacuuming stop device
22. Float valve
5.3 Cleaning the clean-water tank
1. Remove the clean-water tank (3) in the arrow direction, as shown in the assembly section.
Fig. 4
2. Loosen the cap and empty the remaining water. Fig. 23
3. Tighten the cap of the clean water tank again (3) and install the empty tank.
4. Press the power button (1) to turn on the device. Fig. 24
5. Press the water release button (7) to empty the remaining water in the device. Fig. 25
6. When it stops releasing water, turn off the device and unplug it from the mains.
7. Tilt the machine and empty the remaining water at the bottom of the device. Fig. 26
5.4 Cleaning the suction nozzle
1. Press the suction nozzle release button (32) and separate it from the hose bracket (8).
Fig. 27
2. Remove the front cover (33) by lifting it with your finger. Fig. 28
3. Rinse the suction nozzle.
4. Install the suction nozzle cover again. Make sure the pins are correctly placed in the holes
and press these parts until they click. Fig. 29-30
Figure 28-29:
23. Suction nozzle release button
24. Suction nozzle front cover
25. Holes
26. Pins
- When cleaning the suction nozzle, empty the water outlet (20) if clogged. Fig. 31
- Check the hose (5) is not damaged and has no leaks. Fig. 32
5.3 Cleaning the air inlet sponge and the filter sponge
Rinse the air inlet sponge (36) and the filter sponge (37) after every use and replace them if
worn.
ENGLISH
CONGA POPSTAR 3000 CARPETCLEAN 51