mspa Tekapo C-TE062 Manual De Instrucciones página 11

LED display
°C
°F
Once powered-up, press the RESET on the PRCD. The LED displays the current water temperature automatically.
NOTE: The actual water temperature may vary from the temperature displayed on the LED screen by as much as approximately 1°C.
UVC SANITIZER
Press the UVC button to turn the UVC sanitizing system on/off. When the light above this button is green, the UVC sanitizing system is activated.
UVC
UVC
NOTE: The UVC emitter is built inside the control box. Therefore, the function can be turned on at any time, even with people inside the spa.
HEATING
1. Press the HEATER button to turn the heating system on/off. When the light above the heat button is red, the heating system is activated.
HEATER
HEATER
When the light is green, the water is at the set temperature and the heating system is at rest.
20-40°C
2. Pressing the UP or
UP
temperature setting (from 20°C to 40°C ). The new and desired temperature setting will remain on the LED display for 3 seconds to confirm the new
value.
NOTE: The default temperature is 40°C.
NOTE: If the heating system is turned on, the filtration system will automatically start.
NOTE: When the water temperature is below 1°C (33.8°F), the anti-icing system will be activated automatically to heat the water to 3°C (37.4°F).
IMPORTANT: The following conditions will lead to slow water heating
●
An ambient temperature lower than 10°C (50°F).
●
An outdoor wind speed above 3.5-5.4m/s (8-12mph).
●
If the air bubble function is activated when the heater is on.
●
If the spa cover is not properly in place when the heater is on.
FILTRATION
Press the FILTER button to turn the function on/off. The light turns to green when the function is activated.
FILTER
FILTER
NOTE: The filtration system will automatically start when the heating or UVC sanitizing system is activated.
NOTE: After turning off the heating system, the filtration system will automatically stop in 30 seconds.
Filter Cartridge Cleaning Reminder: When the FILTER button is flashing or displays red, the filter cartridge must be cleaned or replaced. Once
this has been done, press the Filter button for 3 seconds to reset the reminder.
Auto-filtration: When the spa is in stand-by mode, the filtration system will operate automatically for 60 minutes every 8 hours.
BUBBLE MASSAGE
Press the BUBBLE button to turn the massage system on/off. The Bubble button displays green when activated.
BUBBLE
BUBBLE
IMPORTANT: Do not turn on the massage system when the cover is attached. Air can accumulate inside the spa and cause irreparable damage
and bodily harm.
NOTE: The bubbling massage function will shut down automatically after every 20 minutes of operation as a safety precaution. This can be
reactivated after 10 minutes by pressing the BUBBLE button again.
HEATING TIMER
TIMER To set the number of hours FROM NOW when the heater will activate:
1-99H
1. Press the TIMER button to enter pre-setting mode. The button displays green.
TIMER
2. Pressing the UP or
UP
activation (from 1 to 99 hours). The desired timer setting will remain on the LED display for 3 seconds to confirm the value.
To modify the timer setting: Press the Timer button again and use the UP or the DOWN button to adjust.
Cancel the setting: Press the TIMER button for 3 seconds.
NOTE: Activating the heating system or rebooting the spa will cancel the timer setting.
SAFETY LOCK
+
UP DOWN
Press the UP and
3s
UP
disabled and the spa retains all previous settings.
Celsius/Fahrenheit Toggle Button
DOWN
The temperature can be displayed in either Celsius or Fahrenheit. Long press
3s
DOWN button will cause the LED to flash. When it is flashing you can adjust the water to the desired
DOWN
DOWN button will cause the LED to flash. While it is flashing, you can adjust the number of hours before heater
DOWN
DOWN buttons at the same time for 3 seconds to lock/unlock the controller. In safety lock mode, the controller is
DOWN
DOWN button for 3 seconds to switch.
DOWN
11