EINHELL TC-MFS 18 Li Manual De Instrucciones Original página 16

Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................... 18 V DC
Idling speed .......................................12000 min
Oscillating speed: ..............................24000 min
Sanding area: ..................... 150 x 150 x 100 mm
Abrasive paper size (Hook-and-loop fastening
system): ................................... 93 x 60 x 105 mm
Oscillatory circuit Ø: ................................ 1.6 mm
Weight: .......................................................0.7 kg
Important!
The equipment is supplied without rechargeable
batteries and without a charger and is allowed to
be used only with the lithium-ion batteries of the
Power-X-Change series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with Power-
X chargers.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 77.2 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 88.2 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
Anl_TC_MFS_18_Li_SPK7.indb 16 Anl_TC_MFS_18_Li_SPK7.indb 16
-1
-1
= 6.585 m/s
2
h
2
- 16 -
GB
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Fitting the dust collection box
(Fig. 2-3/Item 4)
•
Plug the dust collection box (4) onto the vacu-
um cleaner connector (a).
•
The dust is extracted directly into the dust
14.06.2023 08:52:26 14.06.2023 08:52:26