Publicidad
Idiomas disponibles
Idiomas disponibles
Jumper Power Cord
A 432 mm (17") jumper power cord is available as an accessory
that provides a power connection from one Induction Warmer
to another. A total of five units can be connected together off
of one electrical receptacle. The male plug on the jumper cord
connects to the power outlet on the upstream unit, and the
female plug connects to the power inlet on the downstream unit.
Each unit remains independently-controlled.
NOTE: For European units, a total of five units can be
connected together off of one electrical receptacle. For
Chinese and Australian units, a total of four units can be
connected together off of one electrical receptacle.
Female Plug
Jumper Power Cord
Flush Mount Kit
The flush mount kit allows flush-style installation of the unit into
a standard, non-stepped countertop cutout. This installation
requires the purchase of the Flush Mount Kit accessory and can
be performed in a solid material or stainless steel countertop.
IWRMB-FLUSH-MNT = Model IWRM-B1-1313-05
Use the following procedure for flush mount kit installation.
1. Carefully measure and cut the opening in the countertop.
333 mm
(13-1/8")
Flush Mount Kit Installation Countertop Cutout
2. Cut and drill the appropriate holes in the vertical surface
where the control enclosure will be installed. Refer
to the "Installing the Control Panel" procedure in the
INSTALLATION section for details.
3. Cut the required openings in the cabinetry to provide proper
ventilation to the induction range. Refer to the "Ventilation
Requirements" in the INSTALLATION section for details.
4. If necessary, make structural modifications or add bracing
underneath the countertop to ensure the countertop will
support the weight of the unit and its contents.
NOTE: The countertop must be level to ensure proper operation
of the Induction Warmer.
Form No. IWRMCEM-0321
Male Plug
333 mm
(13-1/8")
OPTIONS AND ACCESSORIES
5. Install the two included
mounting brackets to
the underside of the
countertop along two
sides of the cutout, one
across from the other.
• Position the brackets
so
that
there
306 mm (12-1/32") of
clear space between
the brackets; so the
base of the warmer
will fit between the brackets.
• Secure the brackets to the countertop using three of the
included mounting screws for each bracket.
6. Install the included warmer support strips onto the bottom
of the Induction Warmer flange. These strips will help
support the warmer and prevent the silicone sealant from
leaking past the glass. To install a warmer support strip:
a. Remove the existing foam strip present on the bottom of
the Induction Warmer flange.
b. Remove the paper from the adhesive on the support strip.
c. Position the support strip on the flange so that it extends
about 1 mm (1/32") beyond the glass surface on each side.
Underside of
countertop.
Mounting Bracket
Leveling Screw
Installing the Mounting Brackets
7. Install the included leveling screws with lock nuts into the
mounting brackets.
8. Adjust the leveling screws so they are approximately
13 mm (1/2") from the top side of the countertop.
9. Carefully lower the unit into the cutout and set it on top of
the leveling screws. Make sure the power cord and control
cable do not get pinched.
10. Adjust each leveling screw until the glass surface of the
Induction Warmer is level with the countertop.
Silicone
Back
Back
of
of
Unit
Unit
Power Cord
Leveling Screw
Flush Mount Kit Installation
15
Underside of countertop.
Underside of countertop.
306 mm
(12-1/32")
is
Installed
Installed
mounting brackets.
mounting brackets.
Mounting
Screw
Lock Nut
Glass surface level
with countertop.
Front
Front
of
of
Unit
Unit
Countertop
Control Cable Port
Publicidad
