GPI EZ-8 Manual Del Propietario Del Producto página 10

OPERATION
IMPORTANT: Always follow safety precautions when operating this equip-
ment. Review the safety instructions.
OPERATION
IMPORTANT: Always follow safety precautions when operating this equip-
OPERATION
not operate the system in the presence of any source of ignition including running or
ment. Review the safety instructions.
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
IMPORTANT: Always follow safety precautions when operating this equip-
device. A spark can ignite fuel vapors.
ment. Review the safety instructions.
not operate the system in the presence of any source of ignition including running or
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
tight. If damaged, replace hoses before use.
device. A spark can ignite fuel vapors.
not operate the system in the presence of any source of ignition including running or
NOTE: Make sure the work area is dry.
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
device. A spark can ignite fuel vapors.
tight. If damaged, replace hoses before use.
NOTE: Ensure the tank contains enough fuel.
NOTE: Make sure the work area is dry.
tight. If damaged, replace hoses before use.
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
NOTE: Make sure the work area is dry. lids regularly.
Dispensing Fuel
NOTE: Ensure the tank contains enough fuel.
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
Turn on the pump by removing the nozzle from the holder and pushing up the
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
NOTE: Ensure the tank contains enough fuel.
lids regularly.
switch lever. Insert the nozzle into the receiving tank and squeeze the handle
on with the nozzle closed for more than 10 minutes can damage the pump components
to start fuel flow. When done, release the nozzle handle, turn the pump off, and
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
and will void the warranty.
return the nozzle to its holder.
lids regularly.
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
on with the nozzle closed for more than 10 minutes can damage the pump components
IMPORTANT: This is an intermittent duty pump, after running the pump for a
and will void the warranty.
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
maximum of 30 minutes, allow it to cool for 30 minutes.
on with the nozzle closed for more than 10 minutes can damage the pump components
and will void the warranty. IMPORTANT: The motor is provided with an internal temperature-limiting device.
Excessive motor heat will trip the device and will only reset after the motor has cooled.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
maximum of 30 minutes, allow it to cool for 30 minutes.
switch ON again when ready to operate. If the device trips again before the end of the
IMPORTANT: This is an intermittent duty pump, after running the pump for a
duty cycle, see the troubleshooting guide.
IMPORTANT: The motor is provided with an internal temperature-limiting device.
maximum of 30 minutes, allow it to cool for 30 minutes.
Excessive motor heat will trip the device and will only reset after the motor has cooled.
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
IMPORTANT: The motor is provided with an internal temperature-limiting device.
switch ON again when ready to operate. If the device trips again before the end of the
Excessive motor heat will trip the device and will only reset after the motor has cooled.
start pumping.
duty cycle, see the troubleshooting guide.
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
IMPORTANT: This is an intermittent duty pump, after running the pump for a
switch ON again when ready to operate. If the device trips again before the end of the
maximum of 15 minutes, allow it to cool for 30 minutes.
duty cycle, see the troubleshooting guide.
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
start pumping.
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
IMPORTANT: This is an intermittent duty pump, after running the pump for a
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
start pumping.
maximum of 15 minutes, allow it to cool for 30 minutes.
can be reset by turning the switch off and on.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
maximum of 15 minutes, allow it to cool for 30 minutes.
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
can be reset by turning the switch off and on.
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
can be reset by turning the switch off and on.
10
EN
To prevent physical injury or property damage, observe
precautions against fire or explosion when dispensing fuel. Do
To prevent physical injury or property damage, observe
precautions against fire or explosion when dispensing fuel. Do
Before each use, repair leaks around seals or connections.
To prevent physical injury or property damage, observe
Make sure hoses are in good condition and connections are
precautions against fire or explosion when dispensing fuel. Do
Before each use, repair leaks around seals or connections.
Make sure the pump is properly grounded. Repair any corroded
Make sure hoses are in good condition and connections are
or damaged wiring before use.
Before each use, repair leaks around seals or connections.
Make sure hoses are in good condition and connections are
Make sure the pump is properly grounded. Repair any corroded
or damaged wiring before use.
Make sure the pump is properly grounded. Repair any corroded
An automatic bypass valve prevents pressure build up when
the pump is on with the nozzle closed. To avoid pump damage, or damaged wiring before use.
An automatic bypass valve prevents pressure build up when
the pump is on with the nozzle closed. To avoid pump damage,
Never leave the pump running without fluid. Dry running can
An automatic bypass valve prevents pressure build up when
damage the pump components, and will void the warranty.
the pump is on with the nozzle closed. To avoid pump damage,
Never leave the pump running without fluid. Dry running can
damage the pump components, and will void the warranty.
Never leave the pump running without fluid. Dry running can
damage the pump components, and will void the warranty.
Always turn the pump off if the temperature-limiting device
trips. If left on, the pump will automatically reset when cool and
Always turn the pump off if the temperature-limiting device
trips. If left on, the pump will automatically reset when cool and
Always turn the pump off if the temperature-limiting device
trips. If left on, the pump will automatically reset when cool and
1
2
1
1
2
3
2
3
4
3
5
4
4
6
5
5
6
7
6
8
7
9
7
8
8
9
10
9
11
10
12
10
11
11
12
12