KIKKA BOO AMARIS Instrucciones De Uso página 10

IMPORTANT! KEEP FOR FUTURE REFERENCE!
READ CAREFULLY!
•
When using the product at „Co-sleeping function", to prevent a suffocation hazard from entrapment, the bedside sleeper shall be properly secured to the adult
bed using the attachment system.
•
There shall never be a gap between the lower side of the bedside sleeper and the mattress of the adult bed.
•
Check the tightness of the attachment system before each use by pulling the bedside sleeper in a direction away from adult bed.
•
If there is any gap between the bedside sleeper and the adult bed DO NOT use product.
•
Check to make sure that the crib in the co-sleeping mode does not interfere with the parent's bed.
•
The mattress on the parent bed should always be higher than the side of the crib. If not, use the adjusting system to make sure the height is correct on both sides.
•
Before each use, always check that there is no space between the mattress on the parent bed and the wall of the crib. Pull and tighten the attachment system
until the permitted state is restored.
•
Whenever the side wall is lowered, check that the parent mattress position is not changed!
•
When the side wall of the crib is lowered, it should only be used when it is attached to the parent's bed.
•
Use the crib with the wall lowered only in co-sleeping mode.
•
The child may get injured if the amplitude of the swing is excessive.
•
Suspended cribs may pose risks to other children.
•
Other children may pose additional risks (e.g. by swinging the crib excessively).
•
Uneven surfaces can cause instability of the product.
•
Locate suspended cribs in such a way that there is no risk of swing impact ( e.g. no risk of the child hitting the crib frame, or the crib hitting other furniture).
I. PARTS
1. Matress; 2. Mounting strap; 3. Top handrail; 4. Carrycot; 5. Height adjustment lever; 6. Frame leg; 7. Universal wheel; 8. Connecting element;
9. Supporting plastic clip; 10. Baseplate;
II. ASSEMBLING THE BEDSIDE SLEEPER
2.1. Insert the transverse supporting tube into the plastic joint until you hear a clicking sound.
2.2. Insert the Bracket tube into the plastic joint until you hear a clicking sound.
2.3. Insert the supporting tube into the joint until you hear a clicking sound, then insert iron rod into the bassinet set.
2.4. Insert the iron rod into the cloth cover.
2.5. The iron rod which marked in dotted line should be hidden in the cover.
2.6-2.10 Put the ribbon passes through the square hole and fix into D-ring tightly.
2.11. Place the mattress then keep it flat, the bedside sleeper is fully installed.
NOTE! THE BABY COT IS SUITABLE FOR BEDS WITH MINIMUM HEIGHT 52 CM AND MAXIMUM HEIGHT 65 CM.
III. HOW TO DISASSEMBLE THE DROP SIDE
3.1. Unzip the zipper both sides of guardrail.
3.2. Push the button as indicated by the arrow on the button, then upwards the top rail.
3.3. Remove the ends of the guardrail.
3.4. Take down the guardrail tube and lay it flat.
NOTE! ALWAYS COMPLETELY RAISE THE DROP SIDE WHEN NOT ATTACHED TO THE ADULT'S BED!
IV. HOW TO ADJUST THE HEIGHT
HEIGHT SETTING
To change the crib's height, press the height adjustment levers on both ends of the crib and set the carrycot at the desired height. There are seven crib height settings
available. The crib allows setting a different height of each of its ends.
WARNING!
The maximum permitted tilt of the crib carrycot is a difference of two setting levels. Always keep the baby's head in the crib on the higher end of the
carrycot.
WARNING!
When adjusting the height position , make sure the angle of the inclination of the bassinet base end to end (head to feet) shall not be greater than
10°.0r the difference between left and right gears of height shall be smaller than 2°.
4.1. Lift up the plastic height adjust handle both sides, then it comes higher.
4.2. Lift up the plastic height adjust handle both sides, then pull down the nest, it comes lower as you need.
V. CONNECTING WITH ADULT'S BED
WARNING!
When using the bedside bed function, the drop side rail that must be removed and kept well.
WARNING!
When fixing the bedside bed, the short guardrail edge must be closely fitted with the adult mattress to avoid any gap.
NOTE!
When used as a bedside sleeper, the carrycot's bottom must be parallel to the ground. There shall be no difference in height between the crib's ends.
NOTE!
Before each use, make sure there is no gap between the adult's bed mattress and the side of the crib.
WARNING!
This product can only be used with beds and/or mattresses which have straight edges. Do not use this product with any beds and/or mattresses
ENGLISH
w
T
W
5
5
5
5
N
•
•
W
W
a
5
5
B
5
1
2
3
4
t
5
b
6
7
fi
V
6
6
V
•
•
•
•
M
P
C