Publicidad
Idiomas disponibles
Idiomas disponibles
19.3 STORAGE
When not in use, store the anchor in a cool dry area where it will not be exposed to extreme light, extreme heat, excessive
moisture, or possibly corrosive chemicals or materials. Anchor should be hung on a rack or peg or stored flat on a shelf.
20.0 INSPECTION
• Safewaze Anchors shall be inspected prior to each use by the user, and at least annually by a Competent Person other
than the user. Annual inspections shall be documented. Severity of conditions during use may necessitate increased
frequency of documented inspections.
• Anchors that fail inspection MUST be removed from service.
• Prior to each use, inspect the anchor for deficiencies or damage, including, but not limited to, sharp edges, rough
edges, deformations, corrosion, pits, burrs, chemical exposure, extreme heat exposure, kinked, bird nested, or
otherwise damaged cable, and damaged, missing or illegible labels. If any deficiencies or defects are found, the
anchor must IMMEDIATELY be removed from service.
• The anchor must be inspected at least annually by a Competent Person other than the user.
• Competent person inspections must be recorded in the inspection log included in this manual and on the inspection grid
label on the anchor.
21.0 WARRANTY
Safewaze warrants its products are free from defects in materials and construction under normal use and service.
Liability is not accepted for abuse, modification, improper use, destructive activity, and contaminated exposure.
22.0 UNSAFE OR DEFECTIVE CONDITIONS
Equipment inspectors must be trained to look for damage to components of the Beam Anchor. If inspection reveals an
unsafe or defective condition remove the Beam Anchor from service. Refer to the Inspection Form (Section 26.0) of this
manual for inspection specifications.
23.0 PRODUCT LIFE
The working life of Safewaze anchors are determined by work conditions, care and inspection provided. As long as the
anchor passes inspection, it may remain in service.
24.0 DISPOSAL
Dispose of the Safewaze anchor if it has experienced fall arrest forces or inspection reveals an unsafe or defective
condition. Before disposing of the anchor, ensure it is marked as damaged and unsafe for use.
25.0 LABELING
BEAM WALKER EASY SLIDER:
PART#: 021-4068
Fits beams 3-1/2" to 14" width, with
flanges up to 1-1/4"
PART#: 021-4069
225 Wilshire Ave SW
Concord, NC 28025
Fits beams 12" to 30" width, with
USA
(800) 230-0319
flanges up to 2-5/8"
www.safewaze.com
Capacity: ANSI 130-310 lbs (140.61 kg)
XXXXXXX
OSHA Up to 420 lbs (190.5 kg)
S/N
Meets: ANSI Z359.18-2017, OSHA 1910.140, OSHA 1926.502
Sliding Beam Anchor 3.5-15":
PART#: 021-4075
Fits beams 3.5" to 15" width, with flanges
up to 1-1/4"
225 Wilshire Ave SW
Concord, NC 28025
USA
Capacity: ANSI 130-310 lbs (140.61 kg)
(800) 230-0319
www.safewaze.com
OSHA Up to 420 lbs (190.5 kg)
XXXXXXX
S/N
Meets: ANSI Z359.18-2017, OSHA 1910.140, OSHA 1926.502
FIGURE 14 - LABELING
MUST FOLLOW ALL MANUFACTURER'S
INSTRUCTIONS INCLUDED WITH THIS EQUIPMENT
DO NOT REMOVE THIS LABEL
MUST BE INSPECTED BEFORE EACH USE.
MUST BE INSPECTED BY A COMPETENT PERSON AT
LEAST ANNUALLY FROM MFG DATE.
ANY UNIT THAT HAS BEEN SUBJECTED TO FALL ARREST FORCES
MUST BE REMOVED FROM SERVICE.
MINIMUM BREAKING STRENGTH: 5,000 lbf / 22.25 kN
Materials: Stainless Steel, Alloy Steel, and
Aluminum Alloy
021005
MUST FOLLOW ALL MANUFACTURER'S
INSTRUCTIONS INCLUDED WITH THIS EQUIPMENT
DO NOT REMOVE THIS LABEL
MUST BE INSPECTED BEFORE EACH USE.
MUST BE INSPECTED BY A COMPETENT PERSON AT
LEAST ANNUALLY FROM MFG DATE.
ANY UNIT THAT HAS BEEN SUBJECTED TO FALL ARREST FORCES
MUST BE REMOVED FROM SERVICE.
MINIMUM BREAKING STRENGTH: 5,000 lbs / 22.25 kN
Materials: Stainless Steel, Alloy Steel, and
Aluminum Alloy
021003
2023 Copyright Safewaze
WARNING:
MFG. DATE
Compliant fall protection and emergency rescue
systems help prevent serious injury during fall arrest.
MONTH
YEAR
Avoid contact with sharp edges and abrasive
01
02
surfaces. Only make compatible connections. Avoid
03
04
all physical hazards, including, but not limited to,
thermal, electrical and chemical sources. Failure to
05
06
follow all warnings or misuse of equipment could
07
08
result in serious injury or death. For proper
09
10
equipment usage, see user's instructions, visit
11
12
www.safewaze.com or call SAFEWAZE at
(800) 230-0319.
INSPECTION LOG
MONTH
YEAR
021008
10
Publicidad
