Publicidad
Detail View 1: Control Box Section Identification
CONTROL BOX LID
DIN RAIL SECTION 1
WIRE BUNDLE 1
WIRE BUNDLE 2
DIN RAIL SECTION 2
Revision History: LB‐1,800/2,800/4,000C‐220V
Rev No:
Date:
Control System:
V3.0 Firmware
A
02/17/2023
220V Input Voltage
Applicable System Numbers:
LB‐1,800C‐220V
LB‐2,800C‐220V
LB‐4,000C‐220V
List of Symbols: KEY
BLK
WIRE COLOR LABEL – INDICATES A BLACK WIRE
RED
WIRE COLOR LABEL – INDICATES A RED WIRE
WHT
WIRE COLOR LABEL – INDICATES A WHITE WIRE
GRN
WIRE COLOR LABEL – INDICATES A GREEN WIRE
YEL
WIRE COLOR LABEL – INDICATES A YELLOW WIRE
ORG
WIRE COLOR LABEL – INDICATES AN ORANGE WIRE
BLU
WIRE COLOR LABEL – INDICATES A BLUE WIRE
WIRE GAUGE LABEL – INDICATES A GAUGE FOR A CABLE OF MULTIPLE WIRES,
18‐2
FORMATED AS (WIRE GAUGE)‐(NUMBER OF WIRES IN CABLE)
18AWG
WIRE GAUGE LABEL – INDICATES A GAUGE FOR A SINGLE WIRE
CAT5 ETHERNET CONNECTION PORT
USB CONNECTION PORT
LCD‐JST CONNECTION PORT
FUSE – NECESSARY SIZING INFORMATION CALLED OUT ON WIRING DIAGRAM
CABLING – JST AND CAT5 PRE‐FABRICATED CABLES
WIRING – SINGLE WIRE BLACK OR WHITE – TYPICAL COMM COLOR
WIRING – SINGLE WIRE RED – TYPICAL ENERGIZED COLOR
WIRING – SINGLE WIRE YELLOW – TYPICAL NEUTRAL COLOR
WIRING – SINGLE WIRE GREEN – TYPICAL GROUNDING COLOR
WIRING – SINGLE WIRE ORANGE – TYPICAL POWER SIGNALING COLOR
WIRING – SINGLE WIRE BLUE – TYPICAL POWER SIGNALING COLOR
SECTION DIVIDER – CONTROL BOX – NOT A PHYSICAL ELEMNT
WIRING NODE – WIRE BUTT SPLICE CONNECTION
DIODE – ELECTRICAL DIODE – CURRENT FLOW IN DIRECTION OF ARROW
EXTERNAL POWER SOURCE – POWER EXTERNAL TO UNIT, PROVIDED TO UNIT –
220VAC
NOTATION – NOTE CALL OUT INDICATES A NOTE THAT APPLIES TO MULTIPLE AREAS
1
OR PIECES OF HARDWARE – SMALL NUMERIC CIRCLE
NOTATION – WIRE CONTINUITY SYMBOL INDICATES CONTINUITY BETWEEN
A
MATCHING ALPHABETIC SYMBOLS – LARGE ALPHABETIC CIRCLE
JUMPER – INDICATES PLACEMENT AND TERMINATION LOCATION FOR JUMPER –
2 OR 4 PIN – 2 PIN SHOWN
WIRING – PASS THROUGH CONNECTOR – RJ‐45/RJ‐12
Description:
Revision: A
Initial Wiring Diagram for Connect LandBased‐1,800/2,800/4,000 Systems, 220V
Rev Date: 02/17/2023
Print Date: 02/17/2023
Drawn by: LSS
Katadyn Desalination
DIN RAIL SECTION 1
NOTE: WIRES
CONTAINED INSIDE
OF DIN RAIL. SEE
PAGE 2 FOR
CONTINUITY.
14
14AWG
11
14AWG
18AWG
13B
18AWG
5
18AWG
6
18AWG
22
18AWG
NOTE: FOR RESISTOR
SELECTION, FOLLOW THESE
GUIDELINES:
ALL MODELS: 133Ω
NOTE: SILVER BAR OF DIODES
MUST BE FACING AWAY FROM
POWER SOURCE.
LandBased–1,800/2,800/
4,000C–220V
NOTE: SEE PAGE 3 FOR
CONTINUITY.
WIRE BUNDLE 2
WIRE BUNDLE 1
NOTE: REFERANCE
PG. 3 OF WIRING
DIAGRAM FOR FULL
WIRE BUNDLE 2.
A
B
14‐3
C
220 VAC
CONTROL BOX LID
DIN RAIL SECTION 1
PS‐1
NOTE: 220VAC TO
24VDC POWER
SUPPLY
PAGE 1
Publicidad
