Parts And Components - Bravetti FP111B Manual Del Usuario

PARTS AND COMPONENTS

1. Suction Cups
2. Blade Storage Compartment
3. Prep Center Body
4. Swivel Head Release Button
5. Speed Control Dial
6. Turbo Pulse Button
7. Swivel Head
8. Blender Cap
9. Blender Lid
10. Blender Lid Rubber Seal
11. Blender Double Blade
12. Protective Blade Guards (x4)
(For storage purposes only)
13. Blender Main Blade
14. Blender Jar
15. Blender Jar Shaft
16. Food Processor
Food Pusher
Technical Specifications
Voltage: 120V., 60Hz.
Power: 550 Watts
Food Processor Capacity: 6 Cups (1.5 Liters)
Blender Capacity: 7 Cups (1.75 Liters)
Blender Processing Capacity: 6 Cups (1.5 Liters)
* Note: Illustrations may differ from actual product
17. Processor Lid
18. Processor Lid Seal
19. Whipping Blade
20. Processor Double Blade
21. Processor Main Chopping Blade
22. Processor Spindle
23. Food Processor Bowl
24. Processor Bowl Shaft
25. Julienne Blade
26. Grater
27. Thick Shredding Blade
28. Thin Shredding Blade
29. Thick Slicing Blade
30. Thin Slicing Blade
31. Main Blade Holder
32. French Fry Blade
33. French Fry Blade Holder
34. Spatula
3
OPERATING INSTRUCTIONS
Speed Control Dial
The speed control dial has speed
settings as follows:
Off/1-9 + Max
Pulse/Turbo
Pulse
The speed can be
adjusted while the
food processor is
Fig. 1
in use. (Fig. 1)
Use of the Pulse/Turbo
button allows greater control over the
texture of the food being processed. Use
"Pulse" when the unit is in the "Off"
position. Use "Turbo" when the unit is in
the "On" position and you need a burst of
power.
Caution:
The "Pulse" and "Turbo"
function is only intended to be used for
short "bursts" of processing. Damage to
the unit may occur.
Operating the Food Processor
Setting up:
Caution : Make
sure that the unit
is unplugged from
the power source and
the swivel head is in
the off position
before inserting or
Fig. 2
removing any
attachments and before cleaning.
Caution
: Do not operate the unit for
intervals longer than 20 seconds. If
longer chopping or mixing is required, run
for 20 seconds, allow motor to stop and
run again for another 20 seconds.
1. Place the food processor bowl onto
the processor body. (Fig. 2)
Caution:
BLADES ARE SHARP!
Always hold the blade assembly from
the top. ALWAYS remove the
chopping blade protective guards
before using.
2. Assemble the main chopping blade
onto the spindle. Ensure that the tabs
on the underside of the spindle are
aligned with the main chopping blade.
(Fig. 3)
Tabs
Fig. 3
Main Chopping Blade
3. Fit the spindle with chopping blade
onto the motor shaft located on the
bottom of the bowl. (Fig. 4)
Blade & Spindle
Motor Shaft
Fig. 4
4. Fit the processor lid onto the food
processor bowl firmly.
Important
: THE UNIT WILL NOT
OPERATE WITHOUT THE PROCESSOR
LID IN PLACE AND THE SWIVEL HEAD
IN THE LOCKED POSITION.
5. When fitted correctly, the lip on the
processor lid will fit into the notch on
the food processor body. (Fig. 5)
Fig. 5
Lip on
Safety
Cover
6. Turn the swivel head clockwise until
it stops turning and push down until
it "clicks" into place. (Fig. 6)
Unlocked Position Locked Position
Fig. 6
7. Plug in the processor and turn the
speed control dial to the desired
speed. If the processor does not
come on, check that the swivel head
and processor lid are both correctly
fitted and locked into place.
For safety, always
use the food pusher
when putting food into
the feeder tube.
Never feed
by hand. (Fig. 7)
4
Fig. 7