Bosch AdvancedRotak 36V-40-650 Manual Original página 17

Problem Possible Cause
Motor protector has activated
Isolator switch not inserted correctly/fully
Garden tool functions Internal wiring of garden tool defective
intermittently
Motor protector has activated
Machine leaves ragged Height of cut too low
finish
Cutting blade blunt
and/or
Possible clogging
Motor labours
Blade fitted upside down
Blade not rotating Cutting blade obstructed
while garden product
switched on
Blade nut/bolt loose
Excessive vibrations/ Blade nut/bolt loose
noise
Cutting blade damaged
Maintenance and Service
Maintenance, Cleaning and Storage
Before any work on the garden product itself (e. g.
u
maintenance, tool change, etc.) as well as during
transport and storage, remove the battery from the
garden product. There is danger of injury when uninten-
tionally actuating the On/Off switch.
For safe and proper working, always keep the product
u
clean.
Do not place other objects on the garden product.
To ensure safe and efficient operation, always keep the
product and the ventilation slots clean.
Never spray the product with water.
Never immerse the product in water.
Store the product in a secure, dry place, out of the reach of
children.
Do not place other objects on the product.
Keep all nuts, bolts and screws tight to ensure safe working
with the product.
Inspect the product and replace worn or damaged parts for
safety.
Ensure replacement parts fitted are Bosch-approved.
When storing, make sure that all 4 wheels of the garden tool
stand on the ground/floor.
Do not modify this product.Unauthorized modifications
may impair the safety of your product and may result in in-
creased risk of injury.
Battery Maintenance
Use the following procedures to enable optimum usage of
the battery:
– Protect the battery against moisture and water.
Bosch Power Tools
Corrective Action
Allow motor to cool and increase height of cut
Fit correctly
Contact Bosch customer service agent
Allow motor to cool and increase height of cut
Increase height of cut
Replace cutting blade (see figure L)
Switch garden tool off and disengage isolator
switch
Check underneath the garden product and clear
out as necessary (always wear protective gloves)
Refit blade correctly
Switch garden tool off and disengage isolator
switch
Clear obstruction (always wear protective gloves)
Tighten blade nut/bolt (27 Nm)
Tighten blade nut/bolt (27 Nm)
Replace cutting blade (see figure L)
– Store the machine and battery only within a temperature
range between –20 °C and 50 °C . As an example, do not
leave the battery in the car in summer.
– The battery must not be stored within the product but
stored separately.
– Do not leave the battery in the product in direct sunlight.
– The ideal storage condition for the battery is 5 °C.
– Occasionally clean the venting slots of the battery using a
soft, clean and dry brush.
A significantly reduced working period after charging indic-
ates that the battery is used and must be replaced.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
English | 17
F 016 L94 486 | (07.09.2023)