Publicidad
Idiomas disponibles
Idiomas disponibles
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
5.
Service
• Have your power tool serviced by a qualified re-
pair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
WARNING
This power tool generates an electromagnetic field dur-
ing operation. This field can impair active or passive
medical implants under certain conditions. In order to
prevent the risk of serious or deadly injuries, we recom-
mend that persons with medical implants consult with
their physician and the manufacturer of the medical im-
plant prior to operating the power tool.
5.2 Safety instructions for scroll saws
• In an emergency, switch the machine off directly and
pull out the mains plug.
• Observe all of these notes before and while working
with the saw.
• Never use the saw to cut firewood.
• The machine is equipped with a safety switch
against reactivation if the voltage drops.
• If an extension cable is required, make sure that its
cross-section is sufficient for the current consump-
tion of the saw. Minimum cross-section 1.5 mm
• Only use the cable drum when unrolled.
• Personnel working on the machine must not be dis-
tracted.
• Under no circumstances should the saw blades be
braked by pushing against the side after switching
off the drive.
• Only install saw blades that are well sharpened, free
of cracks and not deformed.
• Faulty saw blades must be replaced immediately.
• Do not use saw blades that do not correspond to the
characteristics specified in these usage instructions.
• Ensure that all devices that cover the saw blade
work properly.
• Safety equipment on the machine must not be disas-
sembled or made unusable.
• Damaged or faulty protective devices must be re-
placed immediately.
• Do not cut workpieces that are too small in order to
keep them secure in your hands.
• Do not load the machine so much that it comes to
a standstill.
• Always press the workpiece firmly against the work-
ing plate.
• Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
• Switch off the machine to rectify any faults on the
blocked tool attachment. Pull out the mains plug.
Remove the blockage. Attention! Danger of injury
due to saw blade! Wear protective gloves! Perform
a test run without a workpiece. Make sure that no
unusual noises or vibrations occur. If this is the case,
switch the device off and contact the manufacturer.
• Only carry out modifications, adjustment, measuring
and cleaning work when the engine is switched off.
Pull out the mains plug.
• Before switching on, make sure that keys and adjust-
ing tools are removed.
• Switch off the motor and pull out the mains plug
when leaving the work station.
• Electrical installation, repairs and maintenance work
may only be carried out by specialists.
• All protection and safety equipment must be reas-
sembled immediately after repair or maintenance
work is completed.
• The safety, operating and maintenance information of
the manufacturer, as well as the dimensions specified
in the technical data, must be observed.
• The relevant accident prevention regulations and
the other generally accepted safety rules must be
.
observed.
2
• The saw is only intended for installation indoors.
• Workpieces that are smaller than the saw blade
guard can cause injuries to the hands and fingers.
Use a suitable aid!
• Avoid cramped hand positions when guiding the
workpiece and positions in which the hand would
slip directly into the saw blade.
• Always insert the saw blade so that the teeth point
down towards the saw table.
• Always set the correct blade tension in order to
avoid breaking the saw blades.
• Use extra care when cutting material with irregular
cutting profiles.
• When withdrawing the workpiece, teeth can get
caught in the kerf, especially if the shavings block
the kerf. In this case you should switch off the saw,
pull out the mains plug, open the kerf with a wedge
and remove the workpiece.
www.scheppach.com
GB | 33
Publicidad
