JBM 51837 Manual De Instrucciones página 6

C. Connection between the shooter
and long connecting tube
1. Contact set: Insert one end of
the tube inside diameter of the long
connecting tube and then turn it
clockwise until it is too narrow.
2. Hold both ends of the long con-
necting tube and turn countercloc-
kwise until they are separated.
Function Instruction
1. Turn on
(1). Insert the plug in the socket.
(2). Turn the switch.
According to different occasions, you can select the right accessories
Absorbed brush is Brush is appropriate for your
suitable for flooring, platform, window, table and
carpet, etc. other dirty things.
Protective device
Special instructions for protection device
1. When the water barrel is full, this device will start and the suction power will be suspended at this time; In addition, it will make
some unusual sounds, which means that the machine still works at high speed. When, please cut the power supply quickly this
situation occurs, leave the water outside, and install the machine; The power supply is then connected, the vacuum can continue to
operate normally.
2. It is only suitable plug connects to 220-240 volts and 50 Hz.
3. If the supply cord is damaged, it must be replaced by the manufacturer or a qualified person in its service agent in order to avoid danger.
4. This device is not suitable for people (including children) with reduced physical, sensory or mental capacity, or persons lacking
experience and knowledge, only when a respondent has given security supervision or instructions for use apparatus.
5. Children should be supervised to ensure they do not play with the appliance.
Correct disposal of the product
This mark indicates that this product may not be available with other household waste in EU. To prevent possible damage to the
environment or human health caused by uncontrolled waste disposal, you should recycle it responsibly to promote the sustainable
reuse of material resources.
To return your used device, please use the return and collection systems or contact the store where the product was purchased. They
can take this product as safe recovery.
Special Notes on receipt of the buoy (safety valve)
1. When the water is filling the dust cup, the buoy will start and the suction is suspended at this time; In addition, it will make some
unusual sounds, which means that the machine still works at high speed. When this situation occurs please cut the power supply
quickly, stop outside the water and install the machine; Then connecte the power supply again, and then the vacuum cleaner can
continue to work normally.
2. When the vacuum cleaner is overturned, the buoy will start. Please cut the power supply quickly, place upright vacuum cleaner,
and then connect the power supply again.
3. When the buoy starts, if still using the cleaner could cause engine damage and the event of fire. In that case, we should stop using
it, leave out the water and then reuse.
Maintenance methods
1. Cleaning dust cup. When dust extraction is terminated or has filled the dust container cause the decrease of aspiration. Please
turn off the power supply and clean the garbage into the container.
(1). Dropped the lid and lift.
(2). Remove the filter bag and dust inside the dust cup.
(3). Place the filter bag in the original position.
(They should be placed in the same direction for the switch and the input aperture)
2. Cleaning the filter bag. It should be cleaned with warm water, clean the filter bag for serious obstruction; If necessary, you can use
neutral detergents for cleaning.
(1). Remove the filter bag
(2). Clean it
(3). Dry in the sun
D. Connecting the long connec-
ting tube
1. Contact set: Insert one end of
the long connection pipe inside
diameter of the long connecting
tube, then turn clockwise until it is
too narrow.
2. Hold both ends of the long con-
necting tube and turn countercloc-
kwise until they are separated.
2. Air register
You can adjust the suction power.
When the air register block is
opened, the suction gradually de-
creases; When closed, the suction
gradually increases.
Flat suction nozzle is suitable for cleaning
and dust absorption in crevices, corners
and elsewhere.
· 6 ·
REF.51837
Port puff is suitable for
blowing dust in the crack
of the machine.